Form PHMSA F7000-1.1 PHMSA F7000-1.1 Annual Report for Hazardous Liquid Operators

Pipeline Safety: New Reporting Requirements for Hazardous Liquid Pipeline Operators: Hazardous Liquid Annual Report

HL NPRM Annual Report Form and Instructions - PHMSA F 7000-1_1

Pipeline Safety: New Reporting Requirements for Hazardous Liquid Pipeline Operators: Hazardous Liquid Annual Report

OMB: 2137-0614

⚠️ Notice: This form may be outdated. More recent filings and information on OMB 2137-0614 can be found here:

Document [pdf]

Download: pdf | pdf

Notice: This report is required by 49 CFR Part 195. Failure to report may result in a civil penalty not to exceed $100,000 for each violation
Form Approved
for each day the violation continues up to a maximum of $1,000,000 as provided in 49 USC 60122.
OMB No. 2137-0614
Expires: xy/zz/201x01/31/2014

U.S. Department of Transportation
Pipeline and Hazardous Materials
Safety Administration

INITIAL REPORT

ANNUAL REPORT FOR CALENDAR YEAR 20___
HAZARDOUS LIQUID PIPELINE SYSTEMS

SUPPLEMENTAL REPORT




A federal agency may not conduct or sponsor, and a person is not required to respond to, nor shall a person be subject to a penalty for failure to
comply with a collection of information subject to the requirements of the Paperwork Reduction Act unless that collection of information displays a
current valid OMB Control Number. The OMB Control Number for this information collection is 2137-0614. Public reporting for this collection of
information is estimated to be approximately 18 hours per response, including the time for reviewing instructions, gathering the data needed, and
completing and reviewing the collection of information. All responses to this collection of information are mandatory. Send comments regarding
this burden estimate or any other aspect of this collection of information, including suggestions for reducing this burden to: Information Collection
Clearance Officer, PHMSA, Office of Pipeline Safety (PHP-30) 1200 New Jersey Avenue, SE, Washington, D.C. 20590.
Important: Please read the separate instructions for completeing this form before you begin. They clarify the information requested and provide
specific examples. If you do not have a copy of the instructions, you can obtain one from the PHMSA Pipeline Safety Community Web Page
at http://www.phmsa.dot.gov/pipeline.
PART A - OPERATOR INFORMATION

DOT USE ONLY

1. OPERATOR’S 5 DIGIT IDENTIFICATION NUMBER (OPID)
/

1
ct

2. NAME OF COMPANY OR ESTABLISHMENT:

IF SUBSIDIARY, NAME OF PARENT:

15
20

__________________________________________________

3. INDIVIDUAL WHERE ADDITIONAL INFORMATION MAY BE
OBTAINED:

L
H

Name

Company Name
Street Address

M
PR
N

Title

4. HEADQUARTERS ADDRESS:

__________________________________________________
Email Address

/__/__/__/-/__/__/__/-/__/__/__/__/
Telephone Number

State: /

/ Zip Code: /

/ - /

/__/__/__/-/__/__/__/-/__/__/__/__/
Telephone Number

 Crude Oil
 Refined and/or Petroleum Product (non-HVL)

 HVL

lR
ua

n
An

5. THIS REPORT PERTAINS TO THE FOLLOWING COMMODITY GROUP: (Select Commodity Group based on the predominant commodity
carried and complete the report for that Commodity Group. File a separate report for each Commodity Group included in this OPID.)

 Fuel Grade Ethanol (dedicated system)

 CO 2

6. CHARACTERIZE THE PIPELINES AND/OR PIPELINE FACILITIES COVERED BY THIS OPID AND COMMODITY GROUP WITH
RESPECT TO COMPLIANCE WITH PHMSA’S INTEGRITY MANAGEMENT PROGRAM REGULATIONS (49 CFR 195.452). (Select only one)

 NO portions of the pipelines and/or pipeline facilities covered by this OPID and Commodity
Group are included in an Integrity Management Program subject to 49 CFR 195. If this box is
checked, leave PARTs B, F, G, L, and O blank, but complete all remaining PARTs of this form
in accordance with PART A, Question 8.
 Portions of SOME or ALL of the pipelines and/or pipeline facilities covered by this OPID and
Commodity Group are included in an Integrity Management Program subject to 49 CFR 195. If
this box is checked, complete all PARTs of this form in accordance with PART A, Question 8.

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Pg. 1 of 10
Reproduction of this form is permitted.

7. FOR THE DESIGNATED COMMODITY GROUP, THE PIPELINES AND/OR PIPELINE FACILITIES INCLUDED WITHIN THIS OPID ARE:
(Select one or both)

 INTERstate pipeline  List all of the States in which INTERstate pipelines and/or pipeline
facilities included under this OPID exist: __, __, __, __, __, etc.
 INTRAstate pipeline  List all of the States in which INTRAstate pipelines and/or pipeline
facilities included under this OPID exist: __, __, __, __, __, etc.

8. DOES THIS REPORT REPRESENT A CHANGE FROM LAST YEAR’S FINAL REPORTED NUMBERS FOR ONE OR MORE OF THE
FOLLOWING PARTs: PART B, D, E, H, I, J, K, L, or M? (For calendar year 2010 reporting or if this is a first-time Report for an operator or
OPID, Commodity Group(s), or pipelines and/or pipeline facilities, select the first box only. For subsequent years’ reporting, select either No or
one or both of the Yes choices.)

1
ct

 This report is FOR CALENDAR YEAR 2010 reporting or is a FIRST-TIME REPORT and,
therefore, the remaining choices in this Question 8 do not apply. Complete all remaining
PARTS of this form as applicable.

15
20

 NO, there are NO CHANGES from last year’s final reported information for PARTs B, D, E,
H, I, J, K, L, or M. Complete PARTs A, C, and N, along with PARTs F, G, and O when
applicable.

L
H

M
PR
N

 YES, this report represents a CHANGE FROM LAST YEAR’S FINAL REPORTED
INFORMATION for one or more of PARTs B, D, E, H, I, J, K, L, or M due to corrected
information; however, the pipelines and/or pipeline facilities and operations are the same as
those which were covered under last year’s report. Complete PARTs A, C, and N, along with
only those other PARTs which changed (including PARTs B, F, G, L, and O when applicable).

n
An

lR
ua

 YES, this report represents a CHANGE FROM LAST YEAR’S FINAL REPORTED
INFORMATION for PARTs B, D, E, H, I, J, K, L, or M because of one or more of the following
change(s) in pipelines and/or pipeline facilities and/or operations from those which were
covered under last year’s report. Complete PARTs A, C, and N, along with only those other
PARTs which changed (including PARTs B, F, G, L, and O when applicable). (Select all
reasons for these changes from the following list)

 Merger of companies and/or operations, acquisition of pipelines and/or
pipeline facilities
 Divestiture of pipelines and/or pipeline facilities
 New construction or new installation of pipelines and/or pipeline facilities
 Conversion of service, change in commodity transported, or change in MOP
(maximum operating pressure).
 Abandonment of existing pipelines and/or pipeline facilities
 Change in HCA’s identified, pipeline facilities or segments that could affect
HCAs, or other changes to Operator’s Integrity Management Program
 Change in OPID
 Other  Describe: _______________________________________________

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Pg. 2 of 10
Reproduction of this form is permitted.

For the designated Commodity Group, complete PARTs B, C, D, and E one time for all pipelines and/or
pipeline facilities with regulatory requirements beyond reporting– both INTERstate and INTRAstate included within this OPID. Do not include gathering lines regulated only for reporting in these Parts.
PART B - MILES OF PIPE BY LOCATION
Total Segment Miles
That Could Affect HCAs

Onshore
Offshore
Total Miles

Calc

1
ct

O
PART C - VOLUME TRANSPORTED IN BARREL-MILES (include Commodities within this Commodity Group that are not predominant)

Onshore

Offshore

15
20

Crude Oil

Refined and/or Petroleum Product (non-HVL)
HVL

L
H

CO 2
Fuel Grade Ethanol (dedicated system)

M
PR
N

PART D - MILES OF STEEL PIPE BY CORROSION PROTECTION
Cathodically protected

Coated

Total Miles

Calc

Bare

Calc

Total Miles

Coated
Calc

lR
ua

Onshore
Offshore

n
An

Bare

Cathodically unprotected

Calc

ep
PART E - MILES OF ELECTRIC RESISTANCE WELDED (ERW) PIPE BY WELD TYPE AND DECADE

Pre-40 or
Unknown

1940 -1949

1950 - 1959

1960 - 1969

1970 - 1979

Calc

1990 - 1999

2000 – 2009

2010 - 2019

1980 - 1989

Decade Pipe Installed
High Frequency
Low Frequency and DC
Total Miles
Decade Pipe Installed

Calc
Total Miles

High Frequency

Calc

Low Frequency and DC

Calc

Total Miles

Calc

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Calc

Pg. 3 of 10
Reproduction of this form is permitted.

For the designated Commodity Group, complete PARTs F, and G, and G1 one time for all INTERstate
pipelines and/or pipeline facilities included within this OPID and multiple times as needed for the
designated Commodity Group for each State in which INTRAstate pipelines and/or pipeline facilities
included within this OPID exist. Each time these sections are completed, designate the State to which the
data applies for INTRAstate pipelines and/or pipeline facilities, or that it applies to all INTERstate
pipelines included within this Commodity Group and OPID.
PARTs F and G, and G1
The data reported in these PARTs F and G applies to: (select only one)
 Interstate pipelines/pipeline facilities

1
ct

 Intrastate pipelines/pipeline facilities in the State of /__/__/ (complete for each State)

PART F - INTEGRITY INSPECTIONS CONDUCTED AND ACTIONS TAKEN BASED ON INSPECTION

15
20

1. MILEAGE INSPECTED IN CALENDAR YEAR USING THE FOLLOWING IN-LINE INSPECTION (ILI) TOOLS
a. Corrosion or metal loss tools

L
H

b. Dent or deformation tools

c. Crack or long seam defect detection tools

M
PR
N

d. Any other internal inspection tools

e. Total tool mileage inspected in calendar year using in-line inspection tools. (Lines a + b + c + d )

Calc

2. ACTIONS TAKEN IN CALENDAR YEAR BASED ON IN-LINE INSPECTIONS
a. Based on ILI data, total number of anomalies excavated in calendar year because they met the operator’s
criteria for excavation.

n
An

Calc

b. Total number of anomalies repaired in calendar year that were identified by ILI based on the operator’s criteria,
both within a segment that could affect an HCA and outside of a segment that could affect an HCA.

lR
ua

1. Immediate repair condition
2. 18-month condition

c. Total number of conditions repaired WITHIN A SEGMENT THAT COULD AFFECT AN HCA meeting the
definition of:

3. “180-day condition” [195.452(h)(4)(iii)]

delete

3. MILEAGE INSPECTED AND ACTIONS TAKEN IN CALENDAR YEAR BASED ON PRESSURE TESTING

2. “9-month condition60-day condition” [195.452(h)(4)(ii)]

1. “Immediate repair condition” [195.452(h)(4)(i)]

Calc

a. Total mileage inspected by pressure testing in calendar year.
b. Total number of pressure test failures (ruptures and leaks) repaired in calendar year, both within a segment that
could affect an HCA and outside of a segment that could affect an HCA.
c. Total number of pressure test ruptures (complete failure of pipe wall) repaired in calendar year WITHIN A
SEGMENT THAT COULD AFFECT AN HCA .
d. Total number of pressure test leaks (less than complete wall failure but including escape of test medium)
repaired in calendar year WITHIN A SEGMENT THAT COULD AFFECT AN HCA.

4. MILEAGE INSPECTED AND ACTIONS TAKEN IN CALENDAR YEAR BASED ON ECDA (EXTERNAL COROSION DIRECT
ASSESSMENT)
Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Pg. 4 of 10
Reproduction of this form is permitted.

a. Total mileage inspected by ECDA in calendar year.
b. Total number of anomalies identified by ECDA and repaired in calendar year based on the operator’s criteria,
both within a segment that could affect an HCA and outside of a segment that could affect an HCA.

Calc

1. Immediate repair condition
2. 18-month condition
c. Total number of conditions repaired in calendar year WITHIN A SEGMENT THAT COULD AFFECT AN HCA
meeting the definition of:

Calc

1. “Immediate repair condition” [195.452(h)(4)(i)]
2. 9-month condition“60-day condition” [195.452(h)(4)(ii)]
delete

3. “180-day condition” [195.452(h)(4)(iii)]
5. MILEAGE INSPECTED AND ACTIONS TAKEN IN CALENDAR YEAR BASED ON OTHER INSPECTION TECHNIQUES
a. Total mileage inspected by inspection techniques other than those listed above in calendar year.

Calc

1
ct

b. Total number of anomalies identified by other inspection techniques and repaired in calendar year based on the
operator’s criteria, both within a segment that could affect an HCA and outside of a segment that could affect an
HCA.
1. Immediate repair condition

2. 18-month condition

15
20

c. Total number of conditions repaired in calendar year WITHIN A SEGMENT THAT COULD AFFECT AN HCA
meeting the definition of:

Calc

1. “Immediate repair condition” [195.452(h)(4)(i)]
2. 9-month condition“60-day condition” [195.452(h)(4)(ii)]

L
H

delete

3. “180-day condition” [195.452(h)(4)(iii)]

6. TOTAL MILEAGE INSPECTED (ALL METHODS) AND ACTIONS TAKEN IN CALENDAR YEAR

M
PR
N

Calc

b. Total number of anomalies repaired in calendar year both within a segment that could affect an HCA and outside
of a segment that could affect an HCA. (Lines 2.b1 + 3.b1 + 4.b1 + 5.b1)

Calc

c. Total number of conditions repaired in calendar year WITHIN A SEGMENT THAT COULD AFFECT AN HCA.
(Lines 2.c.1 + 2.c.2 + 2.c.3 + 3.c + 3.d + 4.c.1 + 4.c.2 + 4.c.3 + 5.c.1 + 5.c.2 + 5.c.3)

Calc

lR
ua

n
An

a. Total mileage inspected in calendar year. (Lines 1.e + 3.a + 4.a + 5.a)

PART G – MILES OF BASELINE ASSESSMENTS AND REASSESSMENTS COMPLETED IN CALENDAR YEAR (segment miles that could
affect HCAs ONLY)

Calc

c. Total assessment and reassessment miles completed during the calendar year.

b. Reassessment miles completed during the calendar year.

a. Baseline assessment miles completed during the calendar year.

PART G1 – MILES OF BASELINE ASSESSMENTS AND REASSESSMENTS COMPLETED IN CALENDAR YEAR (outside could affect
HCAs ONLY)
a. Baseline assessment miles completed during the calendar year.
b. Reassessment miles completed during the calendar year.
c. Total assessment and reassessment miles completed during the calendar year.

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Calc

Pg. 5 of 10
Reproduction of this form is permitted.

For the designated Commodity Group, complete PARTs H, I, J, K, K1, L, and M covering INTERstate
pipelines and/or pipeline facilities with regulatory requirements beyond reporting for each State in which
INTERstate systems exist within this OPID and again covering INTRAstate pipelines and/or pipeline
facilities for each State in which INTRAstate systems exist within this OPID. Miles of gathering regulated
only for reporting are included in Part K2 only.
PARTs H, I, J, K, K1, K2, L, and M
The data reported in these PARTs H, I, J, K, L, and M applies to: (select only one)
 Interstate pipelines/pipeline facilities in the State of /__/__/ (complete for each State)

1
ct

 Intrastate Pipelines/pipeline facilities in the State of /__/__/ (complete for each State)

PART H - MILES OF PIPE BY NOMINAL PIPE SIZE (NPS)

15
20

22”

24”

42”

44”

8”

26”

Onshore

Total Miles of Onshore Pipe

12”

14”

16”

18”

20”

28”

30”

32”

34”

36”

38”

52”

56”

58” and
over

48”

Other Pipe Sizes
Not Listed
Size: __ Miles: ________
Add Sizes as needed

n
An

Calc

46”

10”

M
PR
N

6”

L
H

NPS 4”
or less

8”

10”

22”

24”

26”

28”

30”

42”

44”

46”

48”

52”

12”

lR
ua

Offshore

14”

32”

16”

18”

20”

34”

36”

38”

56”

58” and
over

Other Pipe Sizes
Not Listed

Calc

Size: __ Miles: ________
Add Sizes as needed

6”

NPS 4”
or less

Total Miles of Offshore Pipe

PART I - MILES OF PIPE BY DECADE INSTALLED
Pre-20 or Unknown

1920 -1929

1930 -1939

1990 - 1999

2000 - 2009

2010 - 2019

1940 -1949

1950 – 1959

1960 – 1969

1970 – 1979

1980 – 1989

Total Miles
Calc

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Pg. 6 of 10
Reproduction of this form is permitted.

PART J - MILES OF PIPE BY SPECIFIED MINIMUM YIELD STRENGTH
Pipeline Segments Subject to
ALL 49 CFR 195 Requirements
Onshore

Offshore

Rural Low-Stress
Pipeline Segments
Subject ONLY to
Subpart B of
49 CFR 195

Steel Pipe
- Operating at
greater than 20% SMYS

Total Miles

Calc

Non-Rural
Onshore

Rural
Onshore

Offshore

1
ct

O
Steel Pipe
- Operating at less than
or equal to 20% SMYS

Calc

3
Calc

L
H

Total Miles

Calc

n
An

Non-Steel Pipe
- Operating at less than
or equal to 125 psig

Calc

M
PR
N

Non-Steel Pipe
- Operating at
greater than 125 psig

15
20

Steel Pipe
- Operating at an
unknown stress level

Calc

lR
ua

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Pg. 7 of 10
Reproduction of this form is permitted.

PART K - MILES OF SAFETY-REGULATED GATHERING LINES – exclude Gravity Lines and Reporting-Regulated
Gathering
Non-Rural
Onshore

Rural
Onshore

Offshore

Miles that Could
Affect HCA

Total Miles

Calc

Steel Pipe
- Operating at less
than or equal to
20% SMYS

Calc

Non-Steel Pipe
- Operating at
greater than 125
psig

Calc

1
ct

Steel Pipe
- Operating at
greater than 20%
SMYS

15
20

Non-Steel Pipe
- Operating at less
than or equal to
125 psig

Calc

M
PR
N

PART K1 - MILES OF GRAVITY LINES
Steel trunkline operating
at more than 20% SMYS

Calc

L
H

Total Miles

Calc

Trunkline non-steel or
steel operating at 20% or
less SMYS

Gathering non-steel or
steel operating at 20% or
less SMYS

Total
Miles
Calc

n
An

Miles

Steel gathering operating
at more than 20% SMYS

Non-Steel
Greater than 8 6 5/8 to 8 5/8
5/8 inch
inch diameter
diameter

Non-Steel
subTotal

Calc

Total
Total

Calc

Less than 6
5/8 inch
diameter

PART K2 – MILES OF REPORTING-REGULATED GATHERING
Steel
Less than 6 5/8
Greater than 8 5/8
6 5/8 to 8 5/8 inch
Steel
inch diameter and
inch diameter and
diameter
subTotal
operating greater
operating at 20%
than 20% SMYS
or less SMYS
Calc

Calc

lR
ua

Could
Affect
HCA
Miles

PART L – TOTAL SEGMENT MILES THAT COULD AFFECT HCAs
BY TYPE OF HCA
POPULATION AREAS
High Population

NOT BY TYPE

USAs

Other Population

Drinking Water

Ecological
Resource

COMMERCIALLY
NAVIGABLE
WATERWAYS

TOTAL
SEGMENT
MILES THAT
COULD AFFECT
HCA’S

Onshore
Offshore

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Pg. 8 of 10
Reproduction of this form is permitted.

PART M - BREAKOUT TANKS

Total Number of
Tanks Less than or
equal to 50,000 Bbls

Commodity Group

Total Number of
Tanks Over 150,000
Bbls

Total Number of
Tanks 100,001 to
150,000 Bbls

Total Number of
Tanks 50,001
to 100,000 Bbls

Total Number of
Tanks
Calc

Refined and/or Petroleum
Product (non-HVL)

Calc

HVL

Calc

CO2

Calc

Fuel Grade Ethanol
(dedicated system)

Calc

1
ct

Crude Oil

15
20
L
H
M
PR
N
A

lR
ua

n
An

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Pg. 9 of 10
Reproduction of this form is permitted.

For the designated Commodity Group, complete PART N one time for all of the pipelines and/or pipeline
facilities included within this OPID, and then also PART O if any portion(s) of the pipelines and/or pipeline
facilities covered under this Commodity Group and OPID are included in an Integrity Management
Program subject to 49 CFR 195.

PART N - PREPARER SIGNATURE (applicable to all PARTs A - M)

/__/__/__/-/__/__/__/-/__/__/__/__/
Telephone Number

Preparer's Name (type or print)

/__/__/__/-/__/__/__/-/__/__/__/__/
Preparer's Title

Facsimile Number

1
ct

O
Preparer's E-mail Address

3
15
20

L
H

PART O - CERTIFYING SIGNATURE (applicable only to PARTs B, F, G, and L)

M
PR
N

/__/__/__/-/__/__/__/-/__/__/__/__/

Senior Executive Officer’s signature certifying the information in PARTs B, F, G, and L as required by
49 U.S.C. 60109(f)

Telephone Number

Senior Executive Officer’s name certifying the information in PARTs B, F, G, and L as required by
49 U.S.C. 60109(f)

n
An

Senior Executive Officer’s title certifying the information in PARTs B, F, G, and L as required by
49 U.S.C. 60109(f)

lR
ua

Senior Executive Officer’s E-mail Address

Form PHMSA F 7000-1.1 (Rev. Xy-201z06-2011)

Pg. 10 of 10
Reproduction of this form is permitted.

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS

GENERAL INSTRUCTIONS

1
ct

All section references are to Title 49 of the Code of Federal Regulations (49 CFR). The Hazardous
Liquid or Carbon Dioxide Pipeline Systems Annual Report has been revised as of calendar year 2010
affecting submissions for 2010 and beyond. This Annual Report is required per §195.49 and must be
filed per §195.58. Read through the Annual Report and instructions carefully before beginning to
complete the Report. Where common data elements exist between this Report and an operator’s
NPMS submission, the data submitted by the operator on their Annual Report should be the same as
the data submitted through NPMS when possible. (Additionally, and in order to align an operator’s
NPMS submission with their Annual Report data, PHMSA suggests that operators send their NPMS
submission to PHMSA by June 15, representing pipeline assets as of December 31 of the previous
year.)

15
20

L
H

Each operator must annually complete and submit DOT Form PHMSA F 7000–1.1 for each type of
hazardous liquid pipeline facility operated at the end of the previous year. An operator must submit the
annual report by June 15 each year, except that for the 2010 reporting year the report must be
submitted by August 15, 2011. A separate report is required for crude oil, HVL (including anhydrous
ammonia), petroleum products, carbon dioxide pipelines, and fuel grade ethanol pipelines. For each
state a pipeline traverses, an operator must separately complete those sections on the form requiring
information to be reported for each state. In order to improve the accuracy of reported data, operators
are requested to review prior years’ Reports in order to validate that their reported numbers are
accurate, or to identify and correct inconsistencies or errors that are either found or that may exist in
any previously reported data. Operators should file Supplemental Reports as necessary, including
those supplementing prior years’ Reports.

M
PR
N

lR
ua

n
An

The terms “barrel”, “breakout tank”, “carbon dioxide”, “flammable product”, “gathering line”,
“hazardous liquid”, “highly volatile liquid (HVL)”, “intrastate pipeline”, “interstate pipeline”, “low
stress pipeline”, “maximum operating pressure”, “offshore”, “operator”, “Outer Continental Shelf
(OCS)”, “petroleum”, “petroleum product”, “pipe or line pipe”, “pipeline or pipeline system”,
“pipeline facility”, “rural area”, “specified minimum yield strength (SMYS)”, “stress level”, “toxic
product”, and “Unusually Sensitive Area (USA)” are defined in §195.2.
If you need copies of the Form PHMSA F 7000-1.1 and/or instructions they can be found on the
Pipeline Safety Community main page, http://phmsa.dot.gov/pipeline, by clicking Data and Statistics
and then selecting the Forms hyperlink. If you have questions about this Report or these instructions,
please call PHMSA’s Information Resources Manager at 202-366-8075.

Rev. 06-2011

Page 1 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS

ONLINE REPORTING REQUIREMENTS
The following two requirements must be fulfilled prior to submitting data online:
1. You must have an Office of Pipeline Safety (OPS) provided Operator Identification Number (OPID) and
Personal Identification Number (PIN)/password. If you do not have one, please complete and submit
the form located on the OPS Online Data Entry and Operator Registration System New Operator
Registration web site at http://opsweb.phmsa.dot.gov/cfdocs/opsapps/pipes/new_operator.cfm to obtain
one.

1
ct

2. You must have a Username and Password obtained by registering through the PHMSA Portal. If you
have an OPS OPID and PIN/password, you may obtain a Username and Password through the PHMSA
Portal.

15
20

Important: Each operator without an OPID is to plan accordingly and allow for several weeks prior to
the due date of the Report to obtain their OPID from PHMSA.

L
H

M
PR
N

REPORTING METHOD

Annual Reports must be submitted online unless an alternate method is approved (see Alternate
Reporting Methods below). Use the following procedure:

n
An

lR
ua

1. Navigate
to
the
Pipeline
Safety
Community
main
page, http://www.phmsa.dot.gov/pipeline, click the ONLINE DATA ENTRY link
listed.

2. Click on the Annual Hazardous Liquid or Carbon Dioxide Pipeline Systems Report
link

3. Enter Operator Identification Number (OPID) and PIN. [If an operator does not
have an OPID or a PIN, the ONLINE DATA ENTRY page includes directions on
how to obtain one.]
4. Click Add to begin data entry for a new calendar year’s Report. [For Supplemental
Reports, click on the Report ID and select Modify to make corrections or add new
information.]
5. To save intermediate work without formally submitting it to PHMSA, click Save.
6. Click Submit when you have completed the Report (for either an Initial Report or a
Supplemental Report) and are ready to initiate formal submission of your Report to
PHMSA.
7. A confirmation page will appear for you to print and save for your records.
Rev. 06-2011

Page 2 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS

Alternate Reporting Methods
Operators for whom electronic reporting imposes an undue burden and hardship may submit a written
request for an alternate reporting method. Operators must follow the requirements in §195.58(d) to
request an alternate reporting method and must comply with any conditions imposed as part of
PHMSA’s approval of an alternate reporting method.

1
ct

SPECIFIC INSTRUCTIONS

Make an entry in each block for which data is available. Estimate data only if necessary. Avoid
entering any data as UNKNOWN or 0 (zero) except where zero is appropriate to indicate that there
were no instances or amounts of the attribute being reported.

15
20

L
H

Do not report miles of pipe, pipe segments, or pipeline in feet. When reporting mileages that are less
than 1 mile or when reporting portions of a mile, convert feet into a decimal notation (e.g. 2,640 feet =
.5 miles) and report mileage using decimals rounded to the nearest tenth of a mile. Operators may
round all mileages that are greater than 1 mile to the nearest mile. Do not use fractions.

M
PR
N

n
An

Enter the Calendar Year for which the Report is being filed, bearing in mind that reporting
requirements are for the preceding calendar year (i.e., for the June 15, 2011 deadline, the Report
should provide information for assets as they existed at the end of the 2010 calendar year).

lR
ua

Select Initial Report if this is the original filing for the calendar year. Select Supplemental Report if
this is a follow-up to a previously filed Report to amend or correct information for that calendar year.
On Supplemental Reports, enter all information requested in Parts A and N, and only the new or
revised information for the other Parts of the Report, completing Part O as required.

Report miles of pipe, pipe segments, or pipeline in the system at the end of the reporting year,
including any additions or deletions to the system occurring during that year. Report other data for the
duration of the calendar year as appropriate. Adhere to definitions in 49 CFR 195 when reporting
mileage and other data.

Rev. 06-2011

Page 3 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS

1
ct

For a given OPID, a separate Annual Report is to be completed for each Commodity Group
within that OPID. The separate Annual Report is to cover all pipelines and/or pipeline facilities
– both INTERstate and INTRAstate – included within that OPID that serve to transport that
Commodity Group. As an example, if an operator uses a single OPID and has one set of
facilities and/or pipelines that transport crude oil and another that transports refined products,
this operator is to file two Annual Reports – one Annual Report covering all the facilities and/or
pipelines that transport crude oil and another Annual Report covering all the facilities and/or
pipelines that transport refined products. If another operator utilizes two OPIDs with both
crude oil and refined products facilities and/or pipelines within each OPID, that operator must
file four separate Annual Reports.

Parts A – E are to be completed once for each Annual Report, namely once for each Commodity
Group within an OPID, covering ALL of the pipelines and/or facilities (both Interstate and
Intrastate) and combining all states in which those assets exist. Separate reporting by state is not
required for these Parts. Parts F – M, however, are to be reported separately for Interstate and
for Intrastate facilities, or by state, or both depending on the instructions pertaining to each
Part.

15
20

L
H

M
PR
N

PART A - OPERATOR INFORMATION
Complete all 8 sections of Part A before continuing to the next Part.

n
An

1. Operator’s 5 digit Identification Number (OPID)

lR
ua

2. Name of Company or Establishment

All operators that meet the definition of an “operator” under §195.2 must have a PHMSA-assigned
Operator Identification Number (also known as an OPID). If the person completing the Report
does not know the OPID for the system being reported, this information may be requested from
PHMSA’s Information Resources Manager at 202-366-8075. (See instructions on the ONLINE
DATA ENTRY page as described above.)

This is the company name used when registering for an OPID and PIN in the Online Data Entry
System. When completing the Report online, the Name of Operator is automatically filled in based
on the OPID entered in Part A, Question 1. If the name that appears does not coincide with the
OPID, contact PHMSA’s Information Resources Manager.
If the company corresponding to the OPID is a subsidiary, enter the name of the parent company.
3. Individual where additional information may be obtained
Enter the name, title, email address, and telephone number of the individual who should be
contacted if additional information regarding this Report submission is needed.
Rev. 06-2011

Page 4 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS

4. Headquarters address
Enter the address and phone number of the operator’s corporate headquarters.
5. This Report pertains to the following Commodity Group

1
ct

It is a PHMSA requirement (§195.49) that operators submit separate Reports for each Commodity
Group within a particular OPID. It should be noted that these Commodity Groups, though similar
to the Commodity Groups used when reporting accidents to PHMSA, are not precisely the same
when it comes to the reporting of pipelines that transport fuel grade ethanol and ethanol blends.
Whereas fuel grade ethanol and ethanol blends are grouped in the same category for accident
reporting purposes, pipelines that transport fuel grade ethanol have their own Commodity Group
for the purposes of Annual Reporting. Pipelines that transport ethanol in a blended state should be
reported as Refined and/or Petroleum Product (non-HVL) in an operator’s Annual Report.

15
20

L
H

File a separate Annual Report for each of the following Commodity Groups (as further defined
in §195.2):

M
PR
N

Crude Oil - unrefined oil consisting mainly of hydrocarbons.

lR
ua

n
An

Refined and/or Petroleum Product (non-HVL) – flammable, toxic, or corrosive
products obtained from distilling and processing of crude oil, unfinished oils, natural gas
liquids, blend stocks and other miscellaneous hydrocarbon compounds. Examples include
motor gasoline, diesel fuel, fuel oil, aviation gasoline, jet fuel, kerosene, acetone, benzene,
MTBE, naphtha, or other non-HVL petroleum products. For the sake of this Report,
“petroleum product” is meant to be synonymous with “refined product”.

Highly Volatile Liquids (HVLs) – a hazardous liquid which will form a vapor cloud
when released to the atmosphere and which has a vapor pressure exceeding 276 kPa at
37.8º C (100º F). Examples include ethane, ethylene, propane, propylene, butylene, and
anhydrous ammonia (NH 3 ).

Carbon Dioxide (CO 2 ) – a fluid consisting of more than 90 percent carbon dioxide
molecules compressed to a supercritical state.
Fuel Grade Ethanol – a clear, colorless, flammable oxygenated hydrocarbon. Ethanol is
typically produced chemically from ethylene, or biologically from fermentation of various
sugars from carbohydrates found in agricultural crops and cellulosic residues from crops or
wood. This Commodity Group is to be selected only if the pipeline and/or pipeline facility
is used predominantly to transport ethanol which has NOT been blended with petroleum
products. This commodity is sometimes also known as “neat” ethanol. Pipelines that
transport ethanol in a blended state should be reported as Refined and/or Petroleum
Product (non-HVL).
Note: When a single pipeline or facility serves to transport two or more of the above Commodity
Rev. 06-2011

Page 5 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
Groups, that pipeline or facility should be reported only once, reporting within the Commodity
Group for the commodity that is transported most predominantly during the year being reported.
6. Integrity Management Program
Indicate here whether any portion(s) of the pipelines and/or pipeline facilities for this Commodity
Group covered under this OPID are subject to the integrity management (IM) requirements of
§195.452.

1
ct

Pipelines and/or pipeline facilities that include segments that could affect high consequence areas
(HCAs) are required to have an IM Program in accordance with §195.452. For the purposes of this
question and, more generally, this Report, do not consider pipelines or portions of pipelines that
could otherwise not affect an HCA but which are included in an IM Program as a result of other
PHMSA directives (such as Corrective Action Orders, Compliance Orders, Special Permits, etc.).
Select the box indicating that portions of SOME or ALL of the pipelines and/or pipeline facilities
for this Commodity Group covered under this OPID are included in an IM Program as required by
§195.452, and complete other Parts of this Report in accordance with Part A, Question 8.

15
20

L
H

If NO PORTIONS of the pipelines and/or pipeline facilities for this Commodity Group covered
under this OPID are included in an IM Program as required by §195.452, select the box indicating
such. In this case, Parts B, F, G, L, and O need not be completed.

M
PR
N

7. Interstate and/or Intrastate pipeline

lR
ua

n
An

Pipeline assets included within a particular Commodity Group under a single OPID may be either
interstate, intrastate, or both. Select the appropriate box or boxes to indicate whether the pipelines
and/or pipeline facilities for the OPID and Commodity Group are interstate or intrastate or both.
List the two-letter state abbreviation for each state in which reported interstate and/or intrastate
assets are located.

The terms Interstate and Intrastate pipeline are defined in §195.2. Appendix A to 49 CFR 195
contains PHMSA’s Statement of Policy and Interpretation on the delineation between interstate and
intrastate pipelines, and provides additional guidance.

8. Does this Report represent a change from last year’s final reported information for one or
more of the following Parts?
Select “This Report is for calendar year 2010 reporting or is a first-time Report…” only for the
reporting of calendar year 2010 information, including any supplements to that information, or if
this is a first-time filing of an Annual Report for these facilities. Because this revision of the
Annual Report will be used for the first time to report information for calendar year 2010, some of
the “Parts” of this Report referred to in this question are new and, therefore, no comparable
information will have been reported for the prior year. For calendar year 2010 only, respond to this
question by selecting the box “This Report is for calendar year 2010 reporting or is a first-time
Report…”, and then complete all remaining Parts of the Report as applicable. Similarly, if no
Annual Report has been previously filed for this operator, OPID, Commodity Group, or pipelines
and/or pipeline facilities, or for other reasons, select the box “This Report is for calendar year 2010
reporting or is a first-time Report…”, and then complete all remaining Parts of the Report as
Rev. 06-2011

Page 6 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
applicable.
For calendar year submissions beyond 2010, an option has been created to allow the operator to
provide information for relevant Parts when certain portions of the information have not changed.
Select “No” if there are no changes in the information reported for the current reporting year
compared against the prior calendar year for Parts B, D, E, H, I, J, K, L, or M for the Commodity
Group reported.

1
ct

It should be noted that PHMSA expects that the data describing volume transported (Part C) and
integrity management activity (Parts F and G) will change each year. Therefore, Part C, describing
volume transported, must be completed every year. Additionally, those Parts of this Report related
to integrity management activity (Parts F, G and O) must be completed every year by every
operator with portions of pipelines and/or pipeline facilities subject to PHMSA’s IM regulations as
indicated in Part A, Question 6.

15
20

When there are changes in the information reported for the current reporting year compared against
the prior calendar year, these changes can occur for one of the two following reasons:

L
H

M
PR
N

1) New information or new calculations may have changed the understanding of
pipeline and/or pipeline facility data, leading to differences in some data elements
reported on the Annual Report in the previous year’s Report, even though the physical
pipeline(s) and/or pipeline facility(ies) themselves have not changed; or,

lR
ua

n
An

2) The pipeline(s) and/or pipeline facility(ies) may have changed – either physically or
operationally.

Select one or both of the two “Yes” boxes if reported system information has changed.
If the change is due to a change in the pipelines and/or pipeline facilities and/or
operations (number 2 above), select the appropriate box or boxes to indicate the nature
of the change(s). If “Other” is selected, provide a brief description of the change.
Merger/acquisition involves a change in ownership or operating responsibility that
would likely result in increases or other changes in the reported miles of pipeline in
most Parts of the Report.

•

Divestiture involves a change in ownership or operating responsibility that would
likely result in decreases or other changes in the reported miles of pipeline.

•

New construction or new installation that would likely result in increases or other
changes in the reported miles of pipeline, including rerouting of pipelines.

•

Conversion of service, change in commodity transported, or change in MOP
(maximum operating pressure).

•

•
Rev. 06-2011

Conversion to service means conversion to transportation of
Page 7 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
hazardous liquids under §195.5 that would likely result in increases or
other changes in the reported miles of pipeline. (This is selected if a
pipeline that was previously used to transport a commodity or
material that was not covered under 49 CFR 195, such as water, is
being converted to move a commodity that is covered under 49 CFR
195, such as a crude oil line.)
•

Change in MOP (maximum operating pressure) could result in
changes to the mileage of pipeline operating in different categories of
hoop stress (i.e., percent SMYS (Specified Minimum Yield Strength))
as reported in Part J.

15
20

•

1
ct

Change in commodity transported means a change in the commodity
predominately transported and thus in the Commodity Group reported
in Part A, Question 5. (This is selected if the previous commodity
moved in a pipeline covered under 49 CFR 195 is changed to a
different commodity moved under 49 CFR 195, for example a refined
products line being changed to a crude oil line.)

L
H

“Abandoned,” as defined in § 195.2, means permanently removed from service.
All pipeline mileage not permanently removed from service should be reported,
including pipelines and/or pipeline facilities considered to be idled.

•

Change in various aspects of an operator’s IM Program may result in changes to
information reported in Parts B, F, and/or G.

•

Change in an operator’s OPID number – or changes in pipelines and/or pipeline
facilities covered by a particular OPID number – may result in changes throughout
the Annual Report.

M
PR
N

•

lR
ua

n
An

For the designated Commodity Group, complete Parts B, C, D, and E one time for all pipelines
and/or pipeline facilities with regulatory requirments beyond reporting – both INTERstate and
INTRAstate – included within this OPID. Separate reporting by state is not required for these
Parts. Data reported should represent the system in total, including all states in which system
assets are located. Do not include gathering lines regulated only for reporting in these Parts.

PART B - MILES OF PIPE BY LOCATION
Report in Part B the total miles of Onshore and Offshore pipe that could affect High Consequence
Areas (HCAs) and are thus in the IM Program. Operators should NOT double-count mileage for a
single segment of pipeline that may be able to affect HCAs of multiple types (e.g., an Other Population
Area as well as a Drinking Water USA). Also, do not include miles of pipeline that could not affect an
HCA but which are included in the IM Program as a result of other PHMSA directives (such as
Corrective Action Orders, Compliance Orders, Special Permits, etc.). This Part should be left blank if
Rev. 06-2011

Page 8 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
no portions of the pipelines and/or pipeline facilities covered by this OPID are in an IM Program, as
indicated in Part A, Question 6.
PART C – VOLUME TRANSPORTED IN BARREL-MILES

1
ct

Barrel-miles means the total of the number of barrels transported multiplied by the distance in miles
the specific barrels were moved. Report the volume of all commodities transported during the calendar
year for this Commodity Group. Include the annual total volume transported in barrel-miles for all
states and for all pipelines and/or pipeline facilities – both INTERstate and INTRAstate – included
within this OPID and for this Commodity Group. Volumes of any Commodity Group transported in
addition to the Commodity Group predominately transported through these pipelines and/or pipeline
facilities should also be reported in Part C within the proper row. Example: If 2,000,000 barrels of
crude oil were moved in one 35-mile onshore pipeline from end to end and 80,000,000 barrels of crude
oil were moved in a second 1,000-mile onshore pipeline from end to end, both occurring in a given
reporting year, then the total volume transported in barrel-miles for the Crude Oil Commodity Group
for Onshore is equal to (2,000,000 x 35) + (80,000,000 x 1,000) = 70,000,000 + 80,000,000,000 =
80,070,000,000 Onshore Crude Oil Barrel-Miles. If, additionally, 500,000 barrels of an HVL were
moved in the same 35-mile onshore pipeline from end to end, then 17,500,000 barrel-miles (500,000 x
35) should also be included in Part C for the Crude Oil Commodity Group under the “HVL” row and
“Onshore” column in the table.

15
20

L
H

M
PR
N

PART D - MILES OF STEEL PIPE BY CORROSION PROTECTION

n
An

lR
ua

For steel pipe only, report the total miles of Onshore and Offshore pipe that is cathodically protected
and cathodically unprotected subdivided, in each case, into the amount that is bare and the amount that
is coated pipe. COATED means steel pipe coated with an effective hot or cold applied dielectric
coating or wrapper. Enter zero (0) in any cell for which the pipeline system includes no mileage. Do
not leave any cells blank.

PART E – MILES OF ELECTRIC RESISTANCE WELDED (ERW) PIPE BY
WELD TYPE AND DECADE
Report here only pipe that was manufactured using an electric resistance welded (ERW) process.
Report separately, each by decade installed, the miles of installed pipe manufactured using a highfrequency ERW process and that manufactured with a low-frequency or DC ERW process.
“High Frequency” means the ERW pipe was manufactured using a high frequency ERW process.
High frequency ERW pipe is pipe that was manufactured using a high frequency electrical current,
usually about 450 thousand Hertz (kHz) to provide heat for fusion of the weld seam. Most pipe
manufactured using this process has been manufactured since the late 1960s.
“Low Frequency” means the ERW pipe was manufactured using a low frequency ERW process. Low
frequency ERW pipe is pipe that was manufactured using a low frequency, usually about 250 Hertz
Rev. 06-2011

Page 9 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
(Hz) alternating electrical current to provide heat for fusion of the weld seam. Most pipe manufactured
using this process was manufactured prior to 1970.
Flash welded pipe (EFW) is NOT a type of ERW pipe and should NOT be included in the reported
numbers for this Part E.
“DC” means direct current.

1
ct

Make an entry in each block. PHMSA recognizes that some companies may have pipe for which
installation records may not exist. If records do not exist, enter estimates of the totals of such mileage
in the “Pre-40 or Unknown” section of Part E. Enter zero (0) in any block for which the pipeline
system includes no mileage. Do not leave any blocks blank.

15
20

For the designated Commodity Group, complete Parts F and ,G, and G1 one time for all
INTERstate pipelines and/or pipeline facilities included within this OPID and multiple times as
needed for the designated Commodity Group for each State in which INTRAstate pipelines
and/or pipeline facilities included within this OPID exist.

L
H

M
PR
N

For example: Consider a set of crude oil pipeline systems that includes INTERstate pipeline
facilities in seven states and INTRAstate pipeline facilities in three states. Parts F and G should
be completed four times for this set of crude oil pipeline systems – once for all INTERstate assets
(combined) and once for the INTRAstate assets in each of the three states in which INTRAstate
assets are located (separately).

n
An

lR
ua

Each time Parts F, and G, and G1 are completed, indicate whether the data reported is for
INTERstate or INTRAstate pipelines and/or pipeline facilities. If INTRAstate, enter in the space
provided the two-letter postal abbreviation for the state.

PART F - INTEGRITY INSPECTIONS CONDUCTED AND ACTIONS TAKEN
BASED ON INSPECTION

Report all integrity assessments (inspections) required by PHMSA’s IM regulations which were
conducted and actions which were taken during the calendar year based on inspection results. Include
all inspections conducted in the reporting period calendar year including baseline assessments and reassessments. Do not consider pipelines or portions of pipelines that could otherwise not affect an HCA
but which are included in an IM Program as a result of other PHMSA directives (such as Corrective
Action Orders, Compliance Orders, Special Permits, etc.). Part F is subdivided into six (6) sections.
Section 1 - Mileage inspected in calendar year using the following In-Line Inspection (ILI)
tools.
Report the mileage inspected using each of the listed tool types. Include total miles
inspected, not just the mileage that could affect a high consequence area. Where
multiple ILI tools are used (e.g., a metal loss tool and a deformation tool), report the
Rev. 06-2011

Page 10 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
mileage in both categories. Where a combination tool is used (i.e., a single tool with
multiple capabilities), report the mileage separately in each category included as part of
the combination. Thus, the total mileage inspected during the calendar year (the sum of
the mileage reported for individual tools) may be greater than the actual number of
physical pipeline miles on which ILI inspections were run.
Enter zero (0) for any tool which was not used for IM assessments during the year.
Leave no rows blank.
Section 2 - Actions taken in calendar year based on In-Line Inspections.

1
ct

Include all actions taken during the calendar year that resulted from information
obtained during an ILI inspection. This should include actions taken as a result of
information developed during ILI inspections conducted during the calendar year PLUS
actions taken as a result of ILI inspections conducted during prior years and for which
all required actions were not completed during the year of the inspection. Do not
include actions which are anticipated based on review of ILI results but which did not
actually occur during the reporting year.

15
20

L
H

M
PR
N

Report in items a. and b. the total number of anomalies excavated and repaired based on
the operator’s repair criteria even if those criteria are different from (i.e., require repair
of damage more or less significant) than the repair criteria in IM regulations applicable
to anomalies in pipeline segments that could affect HCA. (The operator’s criteria for
anomalies in segments that could affect an HCA must be at least as conservative as
those required by the regulations).

n
An

lR
ua

Report in a. the total number of anomalies excavated, recognizing that multiple
anomalies may be exposed in a single excavation.

Report in b. only those anomalies outside of a could affect HCA area that were repaired
because they met one of theactually repaired condition criteria in PHMSA regulations,
not those for which other mitigative actions (not repair) were undertaken.

Report in c. only the anomalies in pipeline segments that could affect an HCA that were
repaired because they met one of the three repaircondition criteria in the IM regulations.
(The total of repairs reported in item c. should not exceed the total number of repairs
reported in item b.)
Enter a value in each row, using zero (0) as appropriate. Leave no rows blank.
Section 3 – Mileage inspected and actions taken in calendar year based on Pressure
Testing.
Report in a. the total miles inspected by pressure testing, including both mileage that
could affect an HCA and mileage that could not affect an HCA.
Report in b. the total number of test failures (ruptures and leaks) outside of a could
Rev. 06-2011

Page 11 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
affect HCA segment that were repaired on all mileage tested during the year.
Report in c. the ruptures and in d. the leaks repaired ONLY in segments that could
affect an HCA.
Enter a value in each row, using zero (0) as appropriate. Leave no rows blank. Enter
zero (0) in all rows of section 3 if no IM assessments were conducted by pressure test
during the year.
Section 4 - Mileage inspected and actions taken in calendar year based on ECDA
(External Corrosion Direct Assessment)

1
ct

Include all actions taken during the calendar year that resulted from information
obtained during an ECDA inspection. This should include actions taken as a result of
information developed during ECDA inspections conducted during the calendar year
PLUS actions taken as a result of ECDA inspections conducted during prior years and
for which all required actions were not completed during the year of the inspection. Do
not include actions which are anticipated based on ECDA inspection results but which
did not actually occur during the reporting year.

15
20

L
H

M
PR
N

Report in b. the total number of anomalies outside of a could affect HCA area that were
excavated and repaired because they met one of the repair condition criteria in PHMSA
regulations.ased on the operator’s repair criteria even if those criteria are different from
(i.e., require repair of damage more or less significant) than the repair criteria in IM
regulations applicable to anomalies in pipeline segments that could affect an HCA.
(The operator’s criteria for anomalies in segments that could affect an HCA must be at
least as conservative as those required by the regulations).

lR
ua

n
An

Report in c. the number of anomalies in pipeline segments that could affect an HCA that
were repaired because when excavated and examined they met one of the three a repair
condition criteria in the IM regulations.

Enter a value in each row, using zero (0) as appropriate. Leave no rows blank.

Section 5 – Mileage inspected and actions taken in calendar year based on Other
Inspection Techniques
IM regulations allow operators to use other assessment techniques provided that they
notify PHMSA (or states exercising regulatory jurisdiction) in advance. Report here the
mileage inspected and actions taken as a result of inspections conducted using any
technique other than those covered in Sections 1-4 of Part F.
As for the other techniques, include all actions taken during the calendar year that
resulted from information obtained during an inspection using another technique. This
should include actions taken as a result of information developed as part of inspections
conducted during the calendar year PLUS actions taken as a result of inspections
conducted during prior years and for which all required actions were not completed
during the year of the inspection. Do not include actions which are anticipated based on
Rev. 06-2011

Page 12 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
inspection results but which did not actually occur during the reporting year.
Report in b. the total number of anomalies outside of a could affect HCA area that were
excavated and repaired because they met one of the repair condition criteria in PHMSA
regulations.
Report in c. the number of anomalies in pipeline segments that could affect an HCA that
were repaired because when excavated and examined they met a repair condition
criteria in the IM regulations.

1
ct

Report only those anomalies actually repaired, not those for which other mitigative
actions (not repair) were undertaken.

Enter a value in each row, using zero (0) as appropriate. Leave no rows blank.

15
20

Section 6 - Total Mileage Inspected (all Methods) and Actions Taken.

L
H

These entries will be calculated automatically based on data entered in Sections 1-5.
For operators completing a paper form as a result of PHMSA approval to use alternate
reporting measures (see above), report here the total mileage inspected and actions
taken as the sum of the indicated elements from other sections.

M
PR
N

n
An

PART G – MILES OF BASELINE ASSESSMENTS AND REASSESSMENTS COMPLETED
IN CALENDAR YEAR (segment miles that could affect HCAs ONLY)

lR
ua

Report the number of miles of pipeline that could affect an HCA (as reported in Part B) that were
assessed during the calendar year pursuant to §195.452. Report separately the number of miles
inspected for baseline assessments (e.g., initial baseline assessments and new baseline assessments,
including those which occur due to new pipelines or facilities, new or newly identified HCAs, new
spill flow paths, new spill volume calculations, low-stress pipe for which the baseline assessment
deadline has not yet passed, etc.) and miles for which a reassessment was conducted. Do not include
pipelines or portions of pipelines that could otherwise not affect an HCA but which are included in an
IM Program as a result of other PHMSA directives (such as Corrective Action Orders, Compliance
Orders, Special Permits, etc.).
Report only assessments that were completed during the calendar year. These “completed
assessments” are defined consistently with FAQ 4.13 http://primis.phmsa.dot.gov/iim/faqs.htm. The
date on which an assessment is considered complete will be the date on which final field activities
related to that assessment are performed, not including repair activities. That is, when a hydrostatic
test is completed, when the last in-line inspection tool run of a scheduled series of tool runs is
performed, when the last direct examination associated with external corrosion direct assessment is
made, or the date on which "other technology" for which an operator has provided timely notification
is conducted.

Rev. 06-2011

Page 13 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
Operators should report in Part G the total number of miles actually assessed. This differs from Part F
where operators report the number of miles inspected by individual inspection methods where some
mileage may be reported multiple times. Operators should note that the mileages reported as
completed assessments in Part G should be a subset of the total miles of onshore/offshore pipe that
could affect High Consequence Areas reported in Parts B and L. Operators should validate the total
completed and scheduled assessment mileage in their Assessment Plans with the mileage reported
here. The comparison of these two numbers will highlight any discrepancies resulting from new HCA
segments being added or deleted, acquired or sold, or idled 1 or converted, and which need to be
properly reflected in this Report.

1
ct

PART G1 – MILES OF BASELINE ASSESSMENTS AND REASSESSMENTS COMPLETED
IN CALENDAR YEAR (outside could affect HCAs ONLY)

15
20

Report the number of miles of pipeline outside of a could affect HCA area that were assessed during
the calendar year pursuant to PHMSA regulations. Report separately the number of miles inspected
for baseline assessments and miles for which a reassessment was conducted.

L
H

Report only assessments that were completed during the calendar year. The date on which an
assessment is considered complete will be the date on which final field activities related to that
assessment are performed, not including repair activities. That is, when a hydrostatic test is
completed, when the last in-line inspection tool run of a scheduled series of tool runs is performed,
when the last direct examination associated with external corrosion direct assessment is made, or the
date on which "other technology" for which an operator has provided timely notification is conducted.

M
PR
N

n
An

lR
ua

Operators should report in Part G1 the total number of miles actually assessed. This differs from Part
F where operators report the number of miles inspected by individual inspection methods where some
mileage may be reported multiple times.

While the regulations do not recognize an intermediate state between operational and abandoned (see instructions for Part
A, Question 8 above), PHMSA has acknowledged that operators sometimes maintain some of their pipe in an idle status in
which conducting IM assessments is impractical. This consideration of “idle” pipe is discussed in FAQ 2.3 on the PHMSA
IM website (http://primis.phmsa.dot.gov/iim/faqs.htm).

Rev. 06-2011

Page 14 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
For the designated Commodity Group, complete Parts H, I, J, K, K1, L, and M covering
INTERstate pipelines and/or pipeline facilities with regulatory requirements beyond reporting
separately for each State in which INTERstate systems exist within this OPID and again
covering INTRAstate pipelines and/or pipeline facilities separately for each State in which
INTRAstate systems exist within this OPID. Miles of gathering regulated only for reporting are
included in Part K2 only.

1
ct

For example: Consider a set of crude oil pipeline systems that includes INTERstate pipeline
facilities in seven states and INTRAstate pipeline facilities in three states. Parts H, I, J, K, K1,
K2, L, and M should be completed ten times for this set of crude oil pipeline systems – seven
times for INTERstate assets (once for each of the seven states in which INTERstate assets are
located) and once for the INTRAstate assets in each of the three states in which INTRAstate
assets are located.

15
20

Each time the remaining Parts are completed, indicate whether the data reported is for
INTERstate or INTRAstate pipelines and/or pipeline facilities, and enter in the space provided
the two-letter postal abbreviation for the state.

L
H

PART H – MILES OF PIPE BY NOMINAL PIPE SIZE (NPS)

M
PR
N

Report the miles of pipe by Nominal Pipe Size (NPS) and location for both onshore and offshore
locations. Enter the appropriate mileage in the corresponding nominal size blocks.

n
An

Pipe sizes which do not correspond to NPS measurements should be included in the “Other Pipe Sizes
Not Listed” columns. Include both the pipe size and the corresponding mileage.

lR
ua

Enter zero (0) in any block for which the pipeline system includes no mileage. Do not leave any
blocks blank.

ep
R

PART I – MILES OF PIPE BY DECADE INSTALLED

Report the miles of pipe by decade installed. Make an entry in each block including zero (0) when
appropriate. Some companies may have pipe for which installation records may not exist. When the
decade of construction is unknown, enter estimates of the totals of such mileage in the “Pre-20 or
Unknown” section of Part I.
The sum total of pipeline mileage reported in Part I should match the totals reported in Parts H and J.

PART J – MILES OF PIPE BY SPECIFIED MINIMUM YIELD STRENGTH
Report the total miles of steel pipe by hoop stress (as percent of SMYS) and pipe material type (steel
or non-steel) for pipe onshore (in non-rural and rural areas where indicated) and offshore.
Rev. 06-2011

Page 15 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS

Report the total miles of non-steel pipe operating above 125 psig and at or below 125 psig,
differentiated for location as for steel pipe.
Report data only for pipelines regulated by PHMSA (and their certified State agencies) and not those
which are regulated by other federal or state authorities, including those rural, low stress pipeline
segments subject only to Subpart B of 49 CFR 195.
Enter zero (0) in any block for which the pipeline system includes no mileage. Do not leave any
blocks blank.

1
ct

exclude Gravity Lines and Reporting-Regulated Gathering

PART K – MILES OF SAFETY-REGULATED GATHERING LINES – excluding Gravity

Lines and Reporting-Regulated Gathering

15
20

L
H

This Part only applies to the Commodity Group “crude oil” and to those portions of gathering lines that
have are PHMSA regulatory requirements beyond reporting.ed by PHMSA. Report the total mileage
of these safety-regulated gathering lines in three categorieslines only.

M
PR
N

Gathering lines are defined in §195.2 as “A pipeline 219.1mm (8-5/8 inch) or less nominal outside
diameter that transports petroleum from a production facility.” However, do not include any Gravity
Lines in this Part. Gravity Line means a pipeline system where declining elevation provides the
motive force for the commodity.

n
An

Regulated rural gathering lines are defined in §195.11(a) and should be reported in this Part. Enter the
miles of safety-regulated gathering lines that could affect an HCA.

lR
ua

Enter zero (0) in any block for which the pipeline system includes no mileage. Do not leave any
blocks blank.

ep
tP

PART K1 – MILES OF GRAVITY LINES

This Part only applies to the Commodity Group “crude oil”. Gravity Line means a pipeline system
where declining elevation provides the motive force for the commodity. Report the total mileage of
gravity lines in each of the four categories. Report the miles that could affect an HCA in each of the
four categories.
Enter zero (0) in any block for which the pipeline system includes no mileage. Do not leave any
blocks blank.

PART K2 – MILES OF REPORTING-REGULATED GATHERING LINES
This Part only applies to the Commodity Group “crude oil” and to those portions of gathering lines that
have no PHMSA regulatory requirements beyond reporting. Report the total mileage of reportingRev. 06-2011

Page 16 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS
regulated gathering lines in six categories.
Enter zero (0) in any block for which the pipeline system includes no mileage. Do not leave any
blocks blank.

PART L – TOTAL SEGMENT MILES THAT COULD AFFECT HCAs

1
ct

By Type of HCA. Report the miles of pipeline that the operator has determined could affect an HCA
of each designated type. Operators should note that a single segment of pipeline may be able to affect
HCAs of multiple types (e.g., an Other Population Area as well as a Drinking Water USA).
Accordingly, the total of the miles reported in these columns may add to more than the total mileage
that could affect an HCA reported in Part B.

15
20

L
H

Not By Type. Report the total miles of pipeline that the operator has determined could affect an HCA.
For this number, Operators should NOT double-count mileage for a single segment of pipeline that
may be able to affect HCAs of multiple types (e.g., an Other Population Area as well as a Drinking
Water USA). Accordingly, the total of the miles reported in this column, when added for each State,
should equal the total mileage that could affect an HCA reported in Part B.

M
PR
N

Enter zero (0) in any block for which the pipeline system includes no mileage. Do not leave any
blocks blank.

lR
ua

n
An
PART M – BREAKOUT TANKS

List the number of tanks by capacity and by Commodity Group, including any Commodity Groups
which are not the predominantly transported Commodity Group within this Report. The Commodity
Groups listed here in Part M should match those listed in Part C. Operators are required to submit all
breakout tank information in their Annual Report. The operator can also submit their breakout tank
information to NPMS, but breakout tanks must always be reported in their Annual Report.

For the designated Commodity Group, complete Part N one time for all of the pipelines and/or
pipeline facilities included within this OPID. Complete Part O one time for all the pipelines
and/or pipeline facilities covered under this Commodity Group and OPID if any portion(s) of the
pipelines and/or pipeline facilities are included in an IM Program subject to §195.452 as
indicated in Part A, Question 6.

PART N – PREPARER SIGNATURE
Rev. 06-2011

Page 17 of 16

INSTRUCTIONS FOR FORM PHMSA F 7000-1.1 (Rev. 06-2011)
ANNUAL REPORT FOR CALENDAR YEAR 20__
HAZARDOUS LIQUID PIPELINE SYSTEMS

The Preparer is the person who compiled the information and prepared the responses to the Report.
Enter the Preparer’s name and title, and e-mail address if the Preparer has one, as well as the phone
and fax numbers used by the Preparer.

PART O – CERTIFYING SIGNATURE

1
ct

CERTIFYING SIGNATURE must be a senior executive officer of the operator. The Pipeline
Inspection, Protection, Enforcement and Safety Act (signed in December 2006) requires pipeline
operators to have a senior executive officer of the company sign and certify annual pipeline Integrity
Management Program (IMP) performance reports (Parts B, F, G, and L of this Report). By this
signature, the senior executive officer is certifying that he or she has (1) reviewed the Report and (2) to
the best of his or her knowledge, believes the Report is true and complete.

15
20

Senior Executive Officer is the person who is certifying the information on Parts B, F, G, and L as
required by 49 U.S.C. 60109(f).

L
H

M
PR
N

The name and title of the senior executive officer certifying the Report should be entered in the
appropriate blanks on this section of the Report. The name of the senior executive officer certifying
the Report should also be entered in the signature block on the Report. Operators should keep in mind
that entering the senior executive officer’s name onto the electronic Report is equivalent to a paper
submission and has the same legal authenticity and requirements.

lR
ua

n
An

Rev. 06-2011

Page 18 of 16

File Type	application/pdf
Subject	GAS TRANSMISSION/GATHERING SYS
Author	Mark Lepofsky
File Modified	2015-10-13
File Created	2015-10-13