0649ss11

SUPPORTING STATEMENT

ENVIRONMENTAL PROTECTION AGENCY

NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal)

1. Identification of the Information Collection

1(a) Title of the Information Collection

NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal), EPA ICR Number 0649.11, OMB Control Number 2060-0106

1(b) Short Characterization/Abstract

The New Source Performance Standards (NSPS) for Metal Furniture Coating were proposed on November 28, 1980, and promulgated on October 29, 1982. These regulations apply to each metal furniture surface coating operation in which organic coatings are applied (greater than 3,842 liters of coating per year), commencing construction, modification or reconstruction after November 28, 1980. This information is being collected to assure compliance with 40 CFR part 60, subpart EE.

In general, all NSPS standards require initial notifications, performance tests, and periodic reports by the owners/operators of the affected facilities. They are also required to maintain records of the occurrence and duration of any startup, shutdown, or malfunction in the operation of an affected facility, or any period during which the monitoring system is inoperative. These notifications, reports, and records are essential in determining compliance, and are required of all affected facilities subject to NSPS.

Any owner/operator subject to the provisions of this part shall maintain a file of these measurements, and retain the file for at least two years following the date of such measurements, maintenance reports, and records. All reports are sent to the delegated state or local authority. In the event that there is no such delegated authority, the reports are sent directly to the regional offices of the U.S. Environmental Protection Agency (EPA).

Based on our consultations with industry representatives, there is an average of one affected facility at each plant site and that each plant site has only one respondent (i.e., the owner/operator of the plant site).

Over the next three years, an average of 400 respondents per year will be subject to the standard, and no additional respondent per year will become subject to the standard.

The Office of Management and Budget (OMB) approved the currently active Information Collection Request (ICR) without any “Terms of Clearance.”

The “Affected Public” is private sector businesses that perform surface coating of metal furniture products. The burden to the “Affected Public” may be found below in Table 1: Annual Respondent Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal). The burden to the “Federal Government” is attributed entirely to work performed by either Federal employees or government contractors; this burden is found below in Table 2: Average Annual EPA Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal).

2. Need for and Use of the Collection

2(a) Need/Authority for the Collection

The EPA is charged under Section 111 of the Clean Air Act (CAA), as amended, to establish standards of performance for new stationary sources that reflect:

. . . application of the best technological system of continuous emissions reduction which (taking into consideration the cost of achieving such emissions reduction, or any non-air quality health and environmental impact and energy requirements) the Administrator determines has been adequately demonstrated. Section 111(a)(l).

The Agency refers to this charge as selecting the best demonstrated technology (BDT). Section 111 also requires that the Administrator review and, if appropriate, revise such standards every four years.

In the Administrator's judgment, hazard air pollutant emissions from metal furniture coating cause or contribute to air pollution that may reasonably be anticipated to endanger public health or welfare. Therefore, the NSPS were promulgated for this source category at 40 CFR part 60, subpart EE.

2(b) Practical Utility/Users of the Data

The recordkeeping and reporting requirements in the standard ensure compliance with the applicable regulations which where promulgated in accordance with the Clean Air Act. The collected information is also used for targeting inspections and as evidence in legal proceedings.

Performance tests are required in order to determine an affected facility’s initial capability to comply with the emission standard. Continuous emission monitors are used to ensure compliance with the standard at all times. During the performance test a record of the operating parameters under which compliance was achieved may be recorded and used to determine compliance in place of a continuous emission monitor.

The notifications required in the standard are used to inform the Agency or delegated authority when a source becomes subject to the requirements of the regulations. The reviewing authority may then inspect the source to check if the pollution control devices are properly installed and operated and leaks are being detected and repaired and the standard are being met. The performance test may also be observed.

The required semiannual reports are used to determine periods of excess emissions, identify problems at the facility, verify operation/maintenance procedures and for compliance determinations.

3. Non-duplication, Consultations, and Other Collection Criteria

The requested recordkeeping and reporting are required under (40 CFR part 60, subpart EE).

3(a) Non-duplication

If the subject standards have not been delegated, the information is sent directly to the appropriate EPA regional office. Otherwise, the information is sent directly to the delegated state or local agency. If a state or local agency has adopted its own similar standards to implement the Federal standards, a copy of the report submitted to the state or local agency can be sent to the Administrator in lieu of the report required by the Federal standards. Therefore, duplication does not exist.

3(b) Public Notice Required Prior to ICR Submission to OMB

An announcement of a public comment period for the renewal of this ICR was published in the Federal Register (77 FR 47631) on August 9, 2012. No comments were received on the burden published in the Federal Register.

3(c) Consultations

The Agency has consulted industry experts and internal data sources to project the number of affected facilities and industry growth over the next three years. The primary source of information as reported by industry, in compliance with the recordkeeping and reporting provisions in the standard, is the Online Tracking Information System (OTIS) which is operated and maintained by EPA's Office of Compliance. OTIS is EPA’s database for the collection, maintenance, and retrieval of all compliance data. The growth rate for the industry is based on our consultations with the Agency’s internal industry experts.

Industry trade associations and other interested parties were provided an opportunity to comment on the burden associated with the standard as it was being developed and the standard has been previously reviewed to determine the minimum information needed for compliance purposes. In developing this ICR, we contacted: 1) Chromcraft Furniture, at (866) 777-1951; and 2) Winston Furniture Company, Incorporated, at (205) 486-9211.

It is our policy to respond after a thorough review of comments received since the last ICR renewal as well as those submitted in response to the first Federal Register notice. In this case, no comments were received.

3(d) Effects of Less Frequent Collection

Less frequent information collection would decrease the margin of assurance that facilities are continuing to meet the standards. Requirements for information gathering and recordkeeping are useful techniques to ensure that good operation and maintenance practices are applied and emission limitations are met. If the information required by these standards was collected less frequently, the proper operation and maintenance of control equipment and the possibility of detecting violations would be less likely.

3(e) General Guidelines

These reporting or recordkeeping requirements do not violate any of the regulations promulgated by OMB under 5 CFR part 1320, section 1320.5.

3(f) Confidentiality

Any information submitted to the Agency for which a claim of confidentiality is made will be safeguarded according to the Agency policies set forth in Title 40, chapter 1, part 2, subpart B - Confidentiality of Business Information (CBI) (see 40 CFR 2; 41 FR 36902, September 1, 1976; amended by 43 FR 40000, September 8, 1978; 43 FR 42251, September 20, 1978; 44 FR 17674, March 23, 1979).

3(g) Sensitive Questions

The reporting or recordkeeping requirements in the standard do not include sensitive questions.

4. The Respondents and the Information Requested

4(a) Respondents/SIC Codes

The respondents to the recordkeeping and reporting requirements are metal furniture coating facilities. The United States Standard Industrial Classification (SIC) codes for the respondents affected by the standards, which corresponds to the North American Industry Classification System (NAICS) codes, are listed below for metal furniture coating facilities.

Standard (40 CFR Part 60, Subpart EE)	SIC Codes	NAICS Codes
Metal Household Furniture Manufacturing	2514	337124
Office Furniture (except Wood) Manufacturing	2522	337214
Institutional Furniture Manufacturing	2531, 2542	337127
Showcase, Partition, Shelving, and Locker Manufacturing	2542, 2514	337215

4(b) Information Requested

(i) Data Items

In this ICR, all the data that is recorded or reported is required by NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE).

A source must make the following reports:

Notifications
Notification of construction/reconstruction	60.7(a)(1)
Notification of initial performance test	60.8(d)
Notification of actual startup.	60.7(a)(3)
Notification of a physical or operational change.	60.7(a)(4)

Reports
Actual startup	60.7(a)(3)
Initial performance test results	60.8(a)
Demonstration of continuous monitoring system	60.7(a)(5)
Semiannual report	60.7(d)
Excess emissions report	60.7(c), 60.315(b)

A source must keep the following records:

Recordkeeping
Startups, shutdowns, malfunctions, periods where the continuous monitoring system is inoperative.	60.7(b)
Records are required to be retained for two years at the facility.	60.315(d)
Maintain a file of all measurements including the monitoring device, and performance testing measurements, and monitoring device calibrations, checks, adjustments and maintenance performed on these devices.	60.7(e)
Maintain a file of all data and calculations used to determine VOC emissions.	60.315(d)
Maintain daily records of incinerator combustion temperature, or amounts of solvent recovered.	60.315(d)

Electronic Reporting

Some of the respondents are using monitoring equipment that automatically records parameter data. Although personnel at the affected facility must still evaluate the data, internal automation has significantly reduced the burden associated with monitoring and recordkeeping at a plant site.

Also, regulatory agencies in cooperation with the respondents continue to create reporting systems to transmit data electronically. However, electronic reporting systems are still not widely used. At this time, it is estimated that approximately 10 percent of the respondents use electronic reporting.

(ii) Respondent Activities

Respondent Activities

Read instructions.

Install, calibrate, maintain, and operate CMS for temperature for incinerator.

Perform initial performance test, Reference Method 24 test, and repeat performance tests if necessary.

Write the notifications and reports listed above.

Enter information required to be recorded above.

Submit the required reports developing, acquiring, installing, and utilizing technology and systems for the purpose of collecting, validating, and verifying information.

Develop, acquire, install, and utilize technology and systems for the purpose of processing and maintaining information.

Develop, acquire, install, and utilize technology and systems for the purpose of disclosing and providing information.

Adjust the existing ways to comply with any previously applicable instructions and requirements.

Train personnel to be able to respond to a collection of information.

Transmit, or otherwise disclose the information.

Currently sources are using monitoring and reporting equipment that provide parameter data in an automated way e.g., continuous parameter monitoring system. Although personnel at the source still need to evaluate the data, this type of monitoring equipment has significantly reduced the burden associated with monitoring and recordkeeping.

5. The Information Collected: Agency Activities, Collection Methodology, and Information Management

5(a) Agency Activities

EPA conducts the following activities in connection with the acquisition, analysis, storage, and distribution of the required information.

Agency Activities

Observe initial performance tests and repeat performance tests if necessary.

Review notifications and reports, including performance test reports, and excess emissions reports, required to be submitted by industry.

Audit facility records.

Input, analyze, and maintain data in the Online Tracking Information System (OTIS).

5(b) Collection Methodology and Management

Following notification of startup, the reviewing authority could inspect the source to determine whether the pollution control devices are properly installed and operated. Performance test reports are used by the Agency to discern a source’s initial capability to comply with the emission standard. Data and records maintained by the respondents are tabulated and published for use in compliance and enforcement programs. The semiannual reports are used for problem identification, as a check on source operation and maintenance, and for compliance determinations.

Information contained in the reports is entered into OTIS which is operated and maintained by EPA's Office of Compliance. OTIS is EPA’s database for the collection, maintenance, and retrieval of compliance data for approximately 125,000 industrial and government-owned facilities. EPA uses the OTIS for tracking air pollution compliance and enforcement by local and state regulatory agencies, EPA regional offices and EPA headquarters. EPA and its delegated Authorities can edit, store, retrieve and analyze the data.

The records required by this regulation must be retained by the owner/operator for two years.

5(c) Small Entity Flexibility

A majority of the respondents are large entities (i.e., large businesses). However, the impact on small entities (i.e., small businesses) was taken into consideration during the development of the regulation. Due to technical considerations involving the process operations and the types of control equipment employed, the recordkeeping and reporting requirements are the same for both small and large entities. The Agency considers these to be the minimum requirements needed to ensure compliance and, therefore, cannot reduce them further for small entities. To the extent that larger businesses can use economies of scale to reduce their burden, the overall burden will be reduced.

5(d) Collection Schedule

The specific frequency for each information collection activity within this request is shown in below Table 1: Annual Respondent Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal).

6. Estimating the Burden and Cost of the Collection

Table 1 documents the computation of individual burdens for the recordkeeping and reporting requirements applicable to the industry for the subpart included in this ICR. The individual burdens are expressed under standardized headings believed to be consistent with the concept of burden under the Paperwork Reduction Act. Wherever appropriate, specific tasks and major assumptions have been identified. Responses to this information collection are mandatory.

The Agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a currently valid OMB Control Number.

6(a) Estimating Respondent Burden

The average annual burden to industry over the next three years from these recordkeeping and reporting requirements is estimated to be 56,074 (Total Labor Hours from Table 1 below). These hours are based on Agency studies and background documents from the development of the regulation, Agency knowledge and experience with the NSPS program, the previously approved ICR, and any comments received.

6(b) Estimating Respondent Costs

(i) Estimating Labor Costs

This ICR uses the following labor rates:

Managerial $121.44 ($57.83 + 110%)

Technical $100.23 ($47.73 + 110%)

Clerical $50.51 ($24.05 + 110%)

These rates are from the United States Department of Labor, Bureau of Labor Statistics, March 2012, “Table 2. Civilian Workers, by occupational and industry group.” The rates are from column 1, “Total compensation.” The rates have been increased by 110 percent to account for the benefit packages available to those employed by private industry.

(ii) Estimating Capital/Startup and Operation and Maintenance Costs

The type of industry costs associated with the information collection activities in the subject standard are both labor costs which are addressed elsewhere in this ICR and the costs associated with continuous monitoring. The capital/startup costs are one time costs when a facility becomes subject to the regulation. The annual operation and maintenance costs are the ongoing costs to maintain the monitor(s) and other costs such as photocopying and postage.

(iii) Capital/Startup vs. Operation and Maintenance (O&M) Costs

Capital/Startup vs. Operation and Maintenance (O&M) Costs
(A) Continuous Monitoring Device	(B) Capital/Startup Cost for One Respondent	(C) Number of New Respondents	(D) Total Capital/Startup Cost, (B X C)	(E) Annual O&M Costs for One Respondent	(F) Number of Respondents with O&M	(G) Total O&M, (E X F)
Temperature	4,400	0	$0	$2,100	400	$840,000

The total capital/startup costs for this ICR are $0. This is the total of column D in the above table.

The total operation and maintenance (O&M) costs for this ICR are $840,000. This is the total of column G.

The average annual cost for capital/startup and operation and maintenance costs to industry over the next three years of the ICR is estimated to be $840,000. These are recordkeeping costs.

6(c) Estimating Agency Burden and Cost

The only costs to the Agency are those costs associated with analysis of the reported information. EPA's overall compliance and enforcement program includes activities such as the examination of records maintained by the respondents, periodic inspection of sources of emissions, and the publication and distribution of collected information.

The average annual Agency cost during the three years of the ICR is estimated to be $99,503.

This cost is based on the average hourly labor rate as follows:

Managerial $62.27 (GS-13, Step 5, $38.92 + 60%)

Technical $46.21 (GS-12, Step 1, $28.88 + 60%)

Clerical $25.01 (GS-6, Step 3, $15.63 + 60%)

These rates are from the Office of Personnel Management (OPM), 2012 General Schedule, which excludes locality, rates of pay. The rates have been increased by 60 percent to account for the benefit packages available to government employees. Details upon which this estimate is based appear below in Table 2: Average Annual EPA Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal).

6(d) Estimating the Respondent Universe and Total Burden and Costs

Based on our research for this ICR, on average over the next three years, approximately 400 existing respondents will be subject to the standard. It is estimated that no additional respondent per year will become subject. The overall average number of respondents, as shown in the table below is 400 per year.

The number of respondents is calculated using the following table that addresses the three years covered by this ICR.

Number of Respondents
	Respondents That Submit Reports		Respondents That Do Not Submit Any Reports
Year	(A) Number of New Respondents 1	(B) Number of Existing Respondents	(C) Number of Existing Respondents that keep records but do not submit reports	(D) Number of Existing Respondents That Are Also New Respondents	(E) Number of Respondents (E=A+B+C-D)
1	0	400	0	0	400
2	0	400	0	0	400
3	0	400	0	0	400
Average	0	400	0	0	400

¹ New respondents include sources with constructed, reconstructed and modified affected facilities.

.

Column D is subtracted to avoid double-counting respondents. As shown above, the average Number of Respondents over the three year period of this ICR is 400.

The total number of annual responses per year is calculated using the following table:

Total Annual Responses
(A) Information Collection Activity	(B) Number of Respondents	(C) Number of Responses	(D) Number of Existing Respondents That Keep Records But Do Not Submit Reports	(E) Total Annual Responses E=(BxC)+D
Notification of construction/reconstruction	0	1	0	0
Notification of performance test	0	1.2	0	0
Notification of actual startup	0	1	0	0
Report of performance test	0	1.2	0	0
Semiannual report	400	2	0	800
Excess emissions report	80	2	0	160
			Total	960

The number of Total Annual Responses is 960.

The total annual labor costs are $5,429,572. Details regarding these estimates may be found below in Table 1: Annual Respondent Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal).

6(e) Bottom Line Burden Hours and Cost Tables

The detailed bottom line burden hours and cost calculations for the respondents and the Agency are shown in Tables 1 and 2, respectively, and summarized below.

(i) Respondent Tally

The total annual labor hours are 56,074 at a cost of $5,429,572. Details regarding these estimates may be found below in Table 1: Annual Respondent Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal).

Furthermore, the annual public reporting and recordkeeping burden for this collection of information is estimated to average 58 hours per response.

The total annual capital/startup and O&M costs to the regulated entity are $840,000. The cost calculations are detailed in Section 6(b)(iii), Capital/Startup vs. Operation and Maintenance (O&M) Costs.

(ii) The Agency Tally

The average annual Agency burden and cost over next three years is estimated to be 2,208 labor hours at a cost of $99,503. See below Table 2: Average Annual EPA Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal).

6(f) Reasons for Change in Burden

There is no change in the burden hours in this ICR compared to the previous ICR. This is due to two considerations: 1) the regulations have not changed over the past three years and are not anticipated to change over the next three years; and 2) the growth rate for the industry is very low, negative or non-existent, so there is no significant change in the overall burden.

There is an increase in costs for both the respondents and the Agency from the most recently approved ICR. The increase in burden cost is due to an increase in labor rates. This ICR uses updated labor rates from the Bureau of Labor Statistics to calculate burden costs.

6(g) Burden Statement

The annual public reporting and recordkeeping burden for this collection of information is estimated to average 58 hours per response. “Burden” means the total time, effort, or financial resources expended by persons to generate, maintain, retain, or disclose or provide information to or for a Federal agency. This includes the time needed to review instructions; develop, acquire, install, and utilize technology and systems for the purposes of collecting, validating, and verifying information, processing and maintaining information, and disclosing and providing information; adjust the existing ways to comply with any previously applicable instructions and requirements; train personnel to be able to respond to a collection of information; search data sources; complete and review the collection of information; and transmit or otherwise disclose the information.

An agency may not conduct or sponsor, and a person is not required to respond to, a collection of information unless it displays a valid OMB Control Number. The OMB Control Numbers for EPA regulations are listed at 40 CFR part 9 and 48 CFR chapter 15.

To comment on the Agency's need for this information, the accuracy of the provided burden estimates, and any suggested methods for minimizing respondent burden, including the use of automated collection techniques, EPA has established a public docket for this ICR under Docket ID Number EPA-HQ-OECA-2012-0530. An electronic version of the public docket is available at http://www.regulations.gov/ which may be used to obtain a copy of the draft collection of information, submit or view public comments, access the index listing of the contents of the docket, and to access those documents in the public docket that are available electronically. When in the system, select “search,” then key in the docket ID number identified in this document. The documents are also available for public viewing at the Enforcement and Compliance Docket and Information Center in the EPA Docket Center (EPA/DC), EPA West, Room 3334, 1301 Constitution Ave., NW, Washington, DC. The EPA Docket Center Public Reading Room is open from 8:30 a.m. to 4:30 p.m., Monday through Friday, excluding legal holidays. The telephone number for the Reading Room is (202) 566-1744, and the telephone number for the docket center is (202) 566-1752. Also, you can send comments to the Office of Information and Regulatory Affairs, Office of Management and Budget, 725 17th Street, NW, Washington, DC 20503, Attention: Desk Officer for EPA. Please include the EPA Docket ID Number EPA-HQ-OECA-2012-0530 and OMB Control Number 2060-0106 in any correspondence.

Part B of the Supporting Statement

This part is not applicable because no statistical methods were used in collecting this information.

Table 1: Annual Respondent Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal)

	BURDEN ITEM			Hours/ Occurrence (A)	Occurrences/ Year (B)	Hours/Year (C=AxB) (C)	Respondents/ Year b (D)	Technical Person Hours (E=CxD)	Managerial Person Hours (Ex0.05)	Clerical Person Hours (Ex0.10)	Total Costs/Year a (F)
1.	APPLICATIONS			N/A	N/A	N/A	N/A	N/A	N/A	N/A	N/A
2.	SURVEY AND STUDIES			N/A	N/A	N/A	N/A	N/A	N/A	N/A	N/A
3.	REPORTING REQUIREMENTS
	a.	Read Instructions		1	1	1	0	0	0	$0	$0
	b.	Required Activities
			Initial Performance Tests	60	1	60	0	0	0	0	$0
			Repeat Performance Tests	60	0.2	12	0	0	0	0	$0
	c.	Gather Existing Information			------------------------Included in 3b----------------------------
	d.	Write Report
			Notification of Construction/ Reconstruction	2	1	2	0	0	0	0	$0
			Notification of Initial Performance Test	2	1	2	0	0	0	0	$0
			Notification of Actual Startup	2	1	2	0	0	0	0	$0
			Report of Performance Test		------------------------Included in 3b----------------------------
			Semiannual Report c	8	2	16	400	6,400	320	640	$712,659.20
			Excess Emissions Report d	16	2	32	80	2,560	128	256	$285,063.68
	Subtotal for Reporting Requirements							10,304			$997,723
4.	RECORDKEEPING REQUIREMENTS
	a.	Read Instructions			------------------------Included in 3a----------------------------
	b.	Plan Activities			------------------------Included in 3b----------------------------
	c.	Implement Activities (Monthly Performance Test) e		1	12	12	400	4,800	240	480	$534,494.40
	d.	Develop Record System		N/A	N/A	N/A	N/A	N/A	N/A	N/A	N/A
			Records of Operating Parameter f	0.25	350	87.5	400	35,000	1,750	3,500	$3,897,355.00
	Subtotal for Recordkeeping Requirements							45,770			$4,431,849
TOTAL LABOR BURDEN AND COST								56,074			$5,429,572

Assumptions:

^a This ICR uses the following labor rates: $121.44 per hour for Executive, Administrative, and Managerial labor; $100.23 per hour for Technical labor, and $50.51 per hour for Clerical labor. These rates are from the United States Department of Labor, Bureau of Labor Statistics, March 2012, “Table 2. Civilian Workers, by Occupational and Industry group.” The rates are from “column 1, Total Compensation. “ The rates have been increased by 110% to account for the benefit packages available to those employed by private industry.

^b We have assumed that there are approximately 400 respondents, with no additional new or reconstructed sources becoming subject to the rule over the next three

years.

^c We have assumed that each respondent will take eight hours twice per year to complete the semiannual report.

^d We have assumed that 20 percent of respondent will each take 16 hours twice per year to complete the excess emissions reports.

^e We have assumed that each respondent will take one hour once per year to record monthly performance test.

^f We have assumed that each respondent will have 0.25 hours 350 days per year to keep record of operating parameters.

Table 2: Average Annual EPA Burden and Cost – NSPS for Metal Furniture Coating (40 CFR Part 60, Subpart EE) (Renewal)

REPORTING/RECORDKEEPING REQUIREMENT		EPA Hours/Occurrence (A)	Occurrences/Plant/Year (B)	EPA Hours/ Year (C=A*B)	Plants/Year (D)	Technical Person Hours (E=CxD)	Managerial Person Hours (Ex0.05)	Clerical Person Hours (Ex0.10)	Total Costs/Year a (F)
INITIAL PERFORMANCE TESTS
New Plant		24	1	24	0	0	0	0	$0
REPEAT PERFORMANCE TEST
New Plant		24	0.2	4.8	0	0	0	0	$0
REPORT REVIEW
New Plants
	Notification of Construction	2	1	2	0	0	0	0	$0
	Notification of Initial Startup	0.5	1	0.5	0	0	0	0	$0
	Notification of Actual Startup	0.5	1	0.5	0	0	0	0	$0
	Notification of Initial Test	0.5	1.2	0.6	0	0	0	0	$0
	Review Test Results	8	1.2	9.6	0	0	0	0	$0
Existing Plants
	Semiannual Reports	2	2	4	400	1,600	80	160	$82,919.20
	Excess Emissions Reports	2	2	4	80	320	16	32	$16,583.84
TOTAL BURDEN AND COST						2,208			$99,503

Assumptions:

^a This cost is based on the following labor rates which incorporates a 1.6 benefits multiplication factor to account for government overhead expenses: Managerial rate of $62.27 (GS-13, Step 5, $38.92 x 1.6), Technical rate of $46.21 (GS-12, Step 1, $28.88 x 1.6), and Clerical rate of $25.01 (GS-6, Step 3, $15.63 x 1.6). These rates are from the Office of Personnel Management (OPM) 2012 General Schedule which excludes locality rates of pay.

^b We have assumed that it will take two hours twice per year to review the semiannual report.

^c We have assumed that 20 percent of existing plants will each take two hours twice per year to review the excess emissions reports.