29 Cfr 1910.134

Electronic Code of Federal Regulations:

Quick Navigation:

Resources
ResourcesbybyTopic
Topic
Business & Economy

Site Search:
advanced

Home Page > Executive Branch > Code of Federal Regulations > Electronic Code of Federal Regulations

• Browse
• Simple Search

e-CFR Data is current as of December 27, 2011

• Advanced Search
* Boolean
* Proximity
• Search History

Title 29: Labor
PART 1910—OCCUPATIONAL SAFETY AND HEALTH STANDARDS
Subpart I—Personal Protective Equipment

• Search Tips
• Corrections

Browse Previous | Browse Next

• Latest Updates
• User Info

§ 1910.134 Respiratory protection.

• FAQs
• Agency List
• Incorporation by
Reference
• e-CFR Main Page

• Code of Federal
Regulations
• Federal Register
• List of CFR
Sections Affected
• Regulations.gov
• Unified Agenda
• All NARA Publications

Ben's Guide
to U.S.
Government

This section applies to General Industry (part 1910), Shipyards (part 1915), Marine
Terminals (part 1917), Longshoring (part 1918), and Construction (part 1926).
(a) Permissible practice. (1) In the control of those occupational diseases caused by
breathing air contaminated with harmful dusts, fogs, fumes, mists, gases, smokes,
sprays, or vapors, the primary objective shall be to prevent atmospheric
contamination. This shall be accomplished as far as feasible by accepted
engineering control measures (for example, enclosure or confinement of the
operation, general and local ventilation, and substitution of less toxic materials).
When effective engineering controls are not feasible, or while they are being
instituted, appropriate respirators shall be used pursuant to this section.
(2) A respirator shall be provided to each employee when such equipment is
necessary to protect the health of such employee. The employer shall provide the
respirators which are applicable and suitable for the purpose intended. The
employer shall be responsible for the establishment and maintenance of a
respiratory protection program, which shall include the requirements outlined in
paragraph (c) of this section. The program shall cover each employee required by
this section to use a respirator.
(b) Definitions. The following definitions are important terms used in the
respiratory protection standard in this section.
Air-purifying respirator means a respirator with an air-purifying filter, cartridge, or
canister that removes specific air contaminants by passing ambient air through the
air-purifying element.
Assigned protection factor (APF) means the workplace level of respiratory
protection that a respirator or class of respirators is expected to provide to
employees when the employer implements a continuing, effective respiratory

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

protection program as specified by this section.
Atmosphere-supplying respirator means a respirator that supplies the respirator
user with breathing air from a source independent of the ambient atmosphere, and
includes supplied-air respirators (SARs) and self-contained breathing apparatus
(SCBA) units.
Canister or cartridge means a container with a filter, sorbent, or catalyst, or
combination of these items, which removes specific contaminants from the air
passed through the container.
Demand respirator means an atmosphere-supplying respirator that admits breathing
air to the facepiece only when a negative pressure is created inside the facepiece by
inhalation.
Emergency situation means any occurrence such as, but not limited to, equipment
failure, rupture of containers, or failure of control equipment that may or does
result in an uncontrolled significant release of an airborne contaminant.
Employee exposure means exposure to a concentration of an airborne contaminant
that would occur if the employee were not using respiratory protection.
End-of-service-life indicator (ESLI) means a system that warns the respirator user
of the approach of the end of adequate respiratory protection, for example, that the
sorbent is approaching saturation or is no longer effective.
Escape-only respirator means a respirator intended to be used only for emergency
exit.
Filter or air purifying element means a component used in respirators to remove
solid or liquid aerosols from the inspired air.
Filtering facepiece (dust mask) means a negative pressure particulate respirator
with a filter as an integral part of the facepiece or with the entire facepiece
composed of the filtering medium.
Fit factor means a quantitative estimate of the fit of a particular respirator to a
specific individual, and typically estimates the ratio of the concentration of a
substance in ambient air to its concentration inside the respirator when worn.
Fit test means the use of a protocol to qualitatively or quantitatively evaluate the fit
of a respirator on an individual. (See also Qualitative fit test QLFT and
Quantitative fit test QNFT.)
Helmet means a rigid respiratory inlet covering that also provides head protection
against impact and penetration.
High efficiency particulate air (HEPA) filter means a filter that is at least 99.97%
efficient in removing monodisperse particles of 0.3 micrometers in diameter. The
equivalent NIOSH 42 CFR 84 particulate filters are the N100, R100, and P100
filters.
Hood means a respiratory inlet covering that completely covers the head and neck
and may also cover portions of the shoulders and torso.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

Immediately dangerous to life or health (IDLH) means an atmosphere that poses an
immediate threat to life, would cause irreversible adverse health effects, or would
impair an individual's ability to escape from a dangerous atmosphere.
Interior structural firefighting means the physical activity of fire suppression,
rescue or both, inside of buildings or enclosed structures which are involved in a
fire situation beyond the incipient stage. (See 29 CFR 1910.155)
Loose-fitting facepiece means a respiratory inlet covering that is designed to form a
partial seal with the face.
Maximum use concentration (MUC) means the maximum atmospheric
concentration of a hazardous substance from which an employee can be expected
to be protected when wearing a respirator, and is determined by the assigned
protection factor of the respirator or class of respirators and the exposure limit of
the hazardous substance. The MUC can be determined mathematically by
multiplying the assigned protection factor specified for a respirator by the required
OSHA permissible exposure limit, short-term exposure limit, or ceiling limit.
When no OSHA exposure limit is available for a hazardous substance, an employer
must determine an MUC on the basis of relevant available information and
informed professional judgment.
Negative pressure respirator (tight fitting) means a respirator in which the air
pressure inside the facepiece is negative during inhalation with respect to the
ambient air pressure outside the respirator.
Oxygen deficient atmosphere means an atmosphere with an oxygen content below
19.5% by volume.
Physician or other licensed health care professional (PLHCP) means an individual
whose legally permitted scope of practice ( i.e., license, registration, or
certification) allows him or her to independently provide, or be delegated the
responsibility to provide, some or all of the health care services required by
paragraph (e) of this section.
Positive pressure respirator means a respirator in which the pressure inside the
respiratory inlet covering exceeds the ambient air pressure outside the respirator.
Powered air-purifying respirator (PAPR) means an air-purifying respirator that
uses a blower to force the ambient air through air-purifying elements to the inlet
covering.
Pressure demand respirator means a positive pressure atmosphere-supplying
respirator that admits breathing air to the facepiece when the positive pressure is
reduced inside the facepiece by inhalation.
Qualitative fit test (QLFT) means a pass/fail fit test to assess the adequacy of
respirator fit that relies on the individual's response to the test agent.
Quantitative fit test (QNFT) means an assessment of the adequacy of respirator fit
by numerically measuring the amount of leakage into the respirator.
Respiratory inlet covering means that portion of a respirator that forms the
protective barrier between the user's respiratory tract and an air-purifying device or
breathing air source, or both. It may be a facepiece, helmet, hood, suit, or a

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

mouthpiece respirator with nose clamp.
Self-contained breathing apparatus (SCBA) means an atmosphere-supplying
respirator for which the breathing air source is designed to be carried by the user.
Service life means the period of time that a respirator, filter or sorbent, or other
respiratory equipment provides adequate protection to the wearer.
Supplied-air respirator (SAR) or airline respirator means an atmosphere-supplying
respirator for which the source of breathing air is not designed to be carried by the
user.
This section means this respiratory protection standard.
Tight-fitting facepiece means a respiratory inlet covering that forms a complete seal
with the face.
User seal check means an action conducted by the respirator user to determine if
the respirator is properly seated to the face.
(c) Respiratory protection program. This paragraph requires the employer to
develop and implement a written respiratory protection program with required
worksite-specific procedures and elements for required respirator use. The program
must be administered by a suitably trained program administrator. In addition,
certain program elements may be required for voluntary use to prevent potential
hazards associated with the use of the respirator. The Small Entity Compliance
Guide contains criteria for the selection of a program administrator and a sample
program that meets the requirements of this paragraph. Copies of the Small Entity
Compliance Guide will be available on or about April 8, 1998 from the
Occupational Safety and Health Administration's Office of Publications, Room N
3101, 200 Constitution Avenue, NW, Washington, DC, 20210 (202–219–4667).
(1) In any workplace where respirators are necessary to protect the health of the
employee or whenever respirators are required by the employer, the employer shall
establish and implement a written respiratory protection program with worksitespecific procedures. The program shall be updated as necessary to reflect those
changes in workplace conditions that affect respirator use. The employer shall
include in the program the following provisions of this section, as applicable:
(i) Procedures for selecting respirators for use in the workplace;
(ii) Medical evaluations of employees required to use respirators;
(iii) Fit testing procedures for tight-fitting respirators;
(iv) Procedures for proper use of respirators in routine and reasonably foreseeable
emergency situations;
(v) Procedures and schedules for cleaning, disinfecting, storing, inspecting,
repairing, discarding, and otherwise maintaining respirators;
(vi) Procedures to ensure adequate air quality, quantity, and flow of breathing air
for atmosphere-supplying respirators;
(vii) Training of employees in the respiratory hazards to which they are potentially

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

exposed during routine and emergency situations;
(viii) Training of employees in the proper use of respirators, including putting on
and removing them, any limitations on their use, and their maintenance; and
(ix) Procedures for regularly evaluating the effectiveness of the program.
(2) Where respirator use is not required:
(i) An employer may provide respirators at the request of employees or permit
employees to use their own respirators, if the employer determines that such
respirator use will not in itself create a hazard. If the employer determines that any
voluntary respirator use is permissible, the employer shall provide the respirator
users with the information contained in appendix D to this section (“Information
for Employees Using Respirators When Not Required Under the Standard”); and
(ii) In addition, the employer must establish and implement those elements of a
written respiratory protection program necessary to ensure that any employee using
a respirator voluntarily is medically able to use that respirator, and that the
respirator is cleaned, stored, and maintained so that its use does not present a
health hazard to the user. Exception: Employers are not required to include in a
written respiratory protection program those employees whose only use of
respirators involves the voluntary use of filtering facepieces (dust masks).
(3) The employer shall designate a program administrator who is qualified by
appropriate training or experience that is commensurate with the complexity of the
program to administer or oversee the respiratory protection program and conduct
the required evaluations of program effectiveness.
(4) The employer shall provide respirators, training, and medical evaluations at no
cost to the employee.
(d) Selection of respirators. This paragraph requires the employer to evaluate
respiratory hazard(s) in the workplace, identify relevant workplace and user factors,
and base respirator selection on these factors. The paragraph also specifies
appropriately protective respirators for use in IDLH atmospheres, and limits the
selection and use of air-purifying respirators.
(1) General requirements. (i) The employer shall select and provide an appropriate
respirator based on the respiratory hazard(s) to which the worker is exposed and
workplace and user factors that affect respirator performance and reliability.
(ii) The employer shall select a NIOSH-certified respirator. The respirator shall be
used in compliance with the conditions of its certification.
(iii) The employer shall identify and evaluate the respiratory hazard(s) in the
workplace; this evaluation shall include a reasonable estimate of employee
exposures to respiratory hazard(s) and an identification of the contaminant's
chemical state and physical form. Where the employer cannot identify or
reasonably estimate the employee exposure, the employer shall consider the
atmosphere to be IDLH.
(iv) The employer shall select respirators from a sufficient number of respirator
models and sizes so that the respirator is acceptable to, and correctly fits, the user.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(2) Respirators for IDLH atmospheres. (i) The employer shall provide the
following respirators for employee use in IDLH atmospheres:
(A) A full facepiece pressure demand SCBA certified by NIOSH for a minimum
service life of thirty minutes, or
(B) A combination full facepiece pressure demand supplied-air respirator (SAR)
with auxiliary self-contained air supply.
(ii) Respirators provided only for escape from IDLH atmospheres shall be NIOSHcertified for escape from the atmosphere in which they will be used.
(iii) All oxygen-deficient atmospheres shall be considered IDLH. Exception: If the
employer demonstrates that, under all foreseeable conditions, the oxygen
concentration can be maintained within the ranges specified in Table II of this
section (i.e., for the altitudes set out in the table), then any atmosphere-supplying
respirator may be used.
(3) Respirators for atmospheres that are not IDLH. (i) The employer shall provide
a respirator that is adequate to protect the health of the employee and ensure
compliance with all other OSHA statutory and regulatory requirements, under
routine and reasonably foreseeable emergency situations.
(A) Assigned Protection Factors (APFs). Employers must use the assigned
protection factors listed in Table 1 to select a respirator that meets or exceeds the
required level of employee protection. When using a combination respirator (e.g.,
airline respirators with an air-purifying filter), employers must ensure that the
assigned protection factor is appropriate to the mode of operation in which the
respirator is being used.
Table 1—Assigned Protection Factors5

Type of respirator 1,2
1. Air-Purifying Respirator
2. Powered Air-Purifying
Respirator (PAPR)
3. Supplied-Air Respirator
(SAR) or Airline Respirator
• Demand mode
• Continuous flow
mode
• Pressure-demand or
other positive-pressure
mode
4. Self-Contained Breathing
Apparatus (SCBA)
• Demand mode
• Pressure-demand or
other positive-pressure
mode (e.g.,

LooseQuarter Half Full
fitting
mask mask facepiece Helmet/hood facepiece
5 3 10
50
50

1,000

4 25/1,000

25

10
50

50
1,000

4 25/1,000

25

50

1,000

10

50
10,000

50
10,000

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

open/closed circuit)
Notes:
1 Employers

may select respirators assigned for use in higher workplace
concentrations of a hazardous substance for use at lower concentrations of that
substance, or when required respirator use is independent of concentration.

2 The

assigned protection factors in Table 1 are only effective when the employer
implements a continuing, effective respirator program as required by this section
(29 CFR 1910.134), including training, fit testing, maintenance, and use
requirements.

3 This

APF category includes filtering facepieces, and half masks with elastomeric
facepieces.

4 The

employer must have evidence provided by the respirator manufacturer that
testing of these respirators demonstrates performance at a level of protection of
1,000 or greater to receive an APF of 1,000. This level of performance can best be
demonstrated by performing a WPF or SWPF study or equivalent testing. Absent
such testing, all other PAPRs and SARs with helmets/hoods are to be treated as
loose-fitting facepiece respirators, and receive an APF of 25.

5 These

APFs do not apply to respirators used solely for escape. For escape
respirators used in association with specific substances covered by 29 CFR 1910
subpart Z, employers must refer to the appropriate substance-specific standards in
that subpart. Escape respirators for other IDLH atmospheres are specified by 29
CFR 1910.134 (d)(2)(ii).
(B) Maximum Use Concentration (MUC). ( 1 ) The employer must select a
respirator for employee use that maintains the employee's exposure to the
hazardous substance, when measured outside the respirator, at or below the MUC.
( 2 ) Employers must not apply MUCs to conditions that are immediately
dangerous to life or health (IDLH); instead, they must use respirators listed for
IDLH conditions in paragraph (d)(2) of this standard.
( 3 ) When the calculated MUC exceeds the IDLH level for a hazardous substance,
or the performance limits of the cartridge or canister, then employers must set the
maximum MUC at that lower limit.
(ii) The respirator selected shall be appropriate for the chemical state and physical
form of the contaminant.
(iii) For protection against gases and vapors, the employer shall provide:
(A) An atmosphere-supplying respirator, or
(B) An air-purifying respirator, provided that:
( 1 ) The respirator is equipped with an end-of-service-life indicator (ESLI)
certified by NIOSH for the contaminant; or
( 2 ) If there is no ESLI appropriate for conditions in the employer's workplace, the

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

employer implements a change schedule for canisters and cartridges that is based
on objective information or data that will ensure that canisters and cartridges are
changed before the end of their service life. The employer shall describe in the
respirator program the information and data relied upon and the basis for the
canister and cartridge change schedule and the basis for reliance on the data.
(iv) For protection against particulates, the employer shall provide:
(A) An atmosphere-supplying respirator; or
(B) An air-purifying respirator equipped with a filter certified by NIOSH under 30
CFR part 11 as a high efficiency particulate air (HEPA) filter, or an air-purifying
respirator equipped with a filter certified for particulates by NIOSH under 42 CFR
part 84; or
(C) For contaminants consisting primarily of particles with mass median
aerodynamic diameters (MMAD) of at least 2 micrometers, an air-purifying
respirator equipped with any filter certified for particulates by NIOSH.
Table I—Assigned Protection Factors
Table II
Altitude Oxygen deficient Atmospheres (% 02 ) for which the employer may
rely on atmosphere-supplying respirators
(ft.)
Less than 16.0–19.5
3,001
3,001– 16.4–19.5
4,000
4,001– 17.1–19.5
5,000
5,001– 17.8–19.5
6,000
6,001– 18.5–19.5
7,000
7,001– 19.3–19.5.
8,0001
1 Above

8,000 feet the exception does not apply. Oxygen-enriched breathing air
must be supplied above 14,000 feet.
(e) Medical evaluation. Using a respirator may place a physiological burden on
employees that varies with the type of respirator worn, the job and workplace
conditions in which the respirator is used, and the medical status of the employee.
Accordingly, this paragraph specifies the minimum requirements for medical
evaluation that employers must implement to determine the employee's ability to
use a respirator.
(1) General. The employer shall provide a medical evaluation to determine the
employee's ability to use a respirator, before the employee is fit tested or required
to use the respirator in the workplace. The employer may discontinue an
employee's medical evaluations when the employee is no longer required to use a

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

respirator.
(2) Medical evaluation procedures. (i) The employer shall identify a physician or
other licensed health care professional (PLHCP) to perform medical evaluations
using a medical questionnaire or an initial medical examination that obtains the
same information as the medical questionnaire.
(ii) The medical evaluation shall obtain the information requested by the
questionnaire in Sections 1 and 2, part A of appendix C of this section.
(3) Follow-up medical examination. (i) The employer shall ensure that a follow-up
medical examination is provided for an employee who gives a positive response to
any question among questions 1 through 8 in Section 2, part A of appendix C or
whose initial medical examination demonstrates the need for a follow-up medical
examination.
(ii) The follow-up medical examination shall include any medical tests,
consultations, or diagnostic procedures that the PLHCP deems necessary to make a
final determination.
(4) Administration of the medical questionnaire and examinations. (i) The medical
questionnaire and examinations shall be administered confidentially during the
employee's normal working hours or at a time and place convenient to the
employee. The medical questionnaire shall be administered in a manner that
ensures that the employee understands its content.
(ii) The employer shall provide the employee with an opportunity to discuss the
questionnaire and examination results with the PLHCP.
(5) Supplemental information for the PLHCP. (i) The following information must
be provided to the PLHCP before the PLHCP makes a recommendation concerning
an employee's ability to use a respirator:
(A) The type and weight of the respirator to be used by the employee;
(B) The duration and frequency of respirator use (including use for rescue and
escape);
(C) The expected physical work effort;
(D) Additional protective clothing and equipment to be worn; and
(E) Temperature and humidity extremes that may be encountered.
(ii) Any supplemental information provided previously to the PLHCP regarding an
employee need not be provided for a subsequent medical evaluation if the
information and the PLHCP remain the same.
(iii) The employer shall provide the PLHCP with a copy of the written respiratory
protection program and a copy of this section.
Note to paragraph (e)(5)(iii): When the employer replaces a PLHCP, the employer must ensure that the
new PLHCP obtains this information, either by providing the documents directly to the PLHCP or
having the documents transferred from the former PLHCP to the new PLHCP. However, OSHA does
not expect employers to have employees medically reevaluated solely because a new PLHCP has been
selected.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(6) Medical determination. In determining the employee's ability to use a
respirator, the employer shall:
(i) Obtain a written recommendation regarding the employee's ability to use the
respirator from the PLHCP. The recommendation shall provide only the following
information:
(A) Any limitations on respirator use related to the medical condition of the
employee, or relating to the workplace conditions in which the respirator will be
used, including whether or not the employee is medically able to use the respirator;
(B) The need, if any, for follow-up medical evaluations; and
(C) A statement that the PLHCP has provided the employee with a copy of the
PLHCP's written recommendation.
(ii) If the respirator is a negative pressure respirator and the PLHCP finds a
medical condition that may place the employee's health at increased risk if the
respirator is used, the employer shall provide a PAPR if the PLHCP's medical
evaluation finds that the employee can use such a respirator; if a subsequent
medical evaluation finds that the employee is medically able to use a negative
pressure respirator, then the employer is no longer required to provide a PAPR.
(7) Additional medical evaluations. At a minimum, the employer shall provide
additional medical evaluations that comply with the requirements of this section if:
(i) An employee reports medical signs or symptoms that are related to ability to use
a respirator;
(ii) A PLHCP, supervisor, or the respirator program administrator informs the
employer that an employee needs to be reevaluated;
(iii) Information from the respiratory protection program, including observations
made during fit testing and program evaluation, indicates a need for employee
reevaluation; or
(iv) A change occurs in workplace conditions (e.g., physical work effort, protective
clothing, temperature) that may result in a substantial increase in the physiological
burden placed on an employee.
(f) Fit testing. This paragraph requires that, before an employee may be required to
use any respirator with a negative or positive pressure tight-fitting facepiece, the
employee must be fit tested with the same make, model, style, and size of
respirator that will be used. This paragraph specifies the kinds of fit tests allowed,
the procedures for conducting them, and how the results of the fit tests must be
used.
(1) The employer shall ensure that employees using a tight-fitting facepiece
respirator pass an appropriate qualitative fit test (QLFT) or quantitative fit test
(QNFT) as stated in this paragraph.
(2) The employer shall ensure that an employee using a tight-fitting facepiece
respirator is fit tested prior to initial use of the respirator, whenever a different
respirator facepiece (size, style, model or make) is used, and at least annually

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

thereafter.
(3) The employer shall conduct an additional fit test whenever the employee
reports, or the employer, PLHCP, supervisor, or program administrator makes
visual observations of, changes in the employee's physical condition that could
affect respirator fit. Such conditions include, but are not limited to, facial scarring,
dental changes, cosmetic surgery, or an obvious change in body weight.
(4) If after passing a QLFT or QNFT, the employee subsequently notifies the
employer, program administrator, supervisor, or PLHCP that the fit of the
respirator is unacceptable, the employee shall be given a reasonable opportunity to
select a different respirator facepiece and to be retested.
(5) The fit test shall be administered using an OSHA-accepted QLFT or QNFT
protocol. The OSHA-accepted QLFT and QNFT protocols and procedures are
contained in appendix A of this section.
(6) QLFT may only be used to fit test negative pressure air-purifying respirators
that must achieve a fit factor of 100 or less.
(7) If the fit factor, as determined through an OSHA-accepted QNFT protocol, is
equal to or greater than 100 for tight-fitting half facepieces, or equal to or greater
than 500 for tight-fitting full facepieces, the QNFT has been passed with that
respirator.
(8) Fit testing of tight-fitting atmosphere-supplying respirators and tight-fitting
powered air-purifying respirators shall be accomplished by performing quantitative
or qualitative fit testing in the negative pressure mode, regardless of the mode of
operation (negative or positive pressure) that is used for respiratory protection.
(i) Qualitative fit testing of these respirators shall be accomplished by temporarily
converting the respirator user's actual facepiece into a negative pressure respirator
with appropriate filters, or by using an identical negative pressure air-purifying
respirator facepiece with the same sealing surfaces as a surrogate for the
atmosphere-supplying or powered air-purifying respirator facepiece.
(ii) Quantitative fit testing of these respirators shall be accomplished by modifying
the facepiece to allow sampling inside the facepiece in the breathing zone of the
user, midway between the nose and mouth. This requirement shall be accomplished
by installing a permanent sampling probe onto a surrogate facepiece, or by using a
sampling adapter designed to temporarily provide a means of sampling air from
inside the facepiece.
(iii) Any modifications to the respirator facepiece for fit testing shall be completely
removed, and the facepiece restored to NIOSH-approved configuration, before that
facepiece can be used in the workplace.
(g) Use of respirators. This paragraph requires employers to establish and
implement procedures for the proper use of respirators. These requirements include
prohibiting conditions that may result in facepiece seal leakage, preventing
employees from removing respirators in hazardous environments, taking actions to
ensure continued effective respirator operation throughout the work shift, and
establishing procedures for the use of respirators in IDLH atmospheres or in
interior structural firefighting situations.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(1) Facepiece seal protection. (i) The employer shall not permit respirators with
tight-fitting facepieces to be worn by employees who have:
(A) Facial hair that comes between the sealing surface of the facepiece and the face
or that interferes with valve function; or
(B) Any condition that interferes with the face-to-facepiece seal or valve function.
(ii) If an employee wears corrective glasses or goggles or other personal protective
equipment, the employer shall ensure that such equipment is worn in a manner that
does not interfere with the seal of the facepiece to the face of the user.
(iii) For all tight-fitting respirators, the employer shall ensure that employees
perform a user seal check each time they put on the respirator using the procedures
in appendix B–1 or procedures recommended by the respirator manufacturer that
the employer demonstrates are as effective as those in appendix B–1 of this section.
(2) Continuing respirator effectiveness. (i) Appropriate surveillance shall be
maintained of work area conditions and degree of employee exposure or stress.
When there is a change in work area conditions or degree of employee exposure or
stress that may affect respirator effectiveness, the employer shall reevaluate the
continued effectiveness of the respirator.
(ii) The employer shall ensure that employees leave the respirator use area:
(A) To wash their faces and respirator facepieces as necessary to prevent eye or
skin irritation associated with respirator use; or
(B) If they detect vapor or gas breakthrough, changes in breathing resistance, or
leakage of the facepiece; or
(C) To replace the respirator or the filter, cartridge, or canister elements.
(iii) If the employee detects vapor or gas breakthrough, changes in breathing
resistance, or leakage of the facepiece, the employer must replace or repair the
respirator before allowing the employee to return to the work area.
(3) Procedures for IDLH atmospheres. For all IDLH atmospheres, the employer
shall ensure that:
(i) One employee or, when needed, more than one employee is located outside the
IDLH atmosphere;
(ii) Visual, voice, or signal line communication is maintained between the
employee(s) in the IDLH atmosphere and the employee(s) located outside the
IDLH atmosphere;
(iii) The employee(s) located outside the IDLH atmosphere are trained and
equipped to provide effective emergency rescue;
(iv) The employer or designee is notified before the employee(s) located outside
the IDLH atmosphere enter the IDLH atmosphere to provide emergency rescue;
(v) The employer or designee authorized to do so by the employer, once notified,
provides necessary assistance appropriate to the situation;

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(vi) Employee(s) located outside the IDLH atmospheres are equipped with:
(A) Pressure demand or other positive pressure SCBAs, or a pressure demand or
other positive pressure supplied-air respirator with auxiliary SCBA; and either
(B) Appropriate retrieval equipment for removing the employee(s) who enter(s)
these hazardous atmospheres where retrieval equipment would contribute to the
rescue of the employee(s) and would not increase the overall risk resulting from
entry; or
(C) Equivalent means for rescue where retrieval equipment is not required under
paragraph (g)(3)(vi)(B).
(4) Procedures for interior structural firefighting. In addition to the requirements
set forth under paragraph (g)(3), in interior structural fires, the employer shall
ensure that:
(i) At least two employees enter the IDLH atmosphere and remain in visual or
voice contact with one another at all times;
(ii) At least two employees are located outside the IDLH atmosphere; and
(iii) All employees engaged in interior structural firefighting use SCBAs.
Note 1 to paragraph (g): One of the two individuals located outside the IDLH atmosphere may be
assigned to an additional role, such as incident commander in charge of the emergency or safety
officer, so long as this individual is able to perform assistance or rescue activities without jeopardizing
the safety or health of any firefighter working at the incident.
Note 2 to paragraph (g): Nothing in this section is meant to preclude firefighters from performing
emergency rescue activities before an entire team has assembled.

(h) Maintenance and care of respirators. This paragraph requires the employer to
provide for the cleaning and disinfecting, storage, inspection, and repair of
respirators used by employees.
(1) Cleaning and disinfecting. The employer shall provide each respirator user with
a respirator that is clean, sanitary, and in good working order. The employer shall
ensure that respirators are cleaned and disinfected using the procedures in appendix
B–2 of this section, or procedures recommended by the respirator manufacturer,
provided that such procedures are of equivalent effectiveness. The respirators shall
be cleaned and disinfected at the following intervals:
(i) Respirators issued for the exclusive use of an employee shall be cleaned and
disinfected as often as necessary to be maintained in a sanitary condition;
(ii) Respirators issued to more than one employee shall be cleaned and disinfected
before being worn by different individuals;
(iii) Respirators maintained for emergency use shall be cleaned and disinfected
after each use; and
(iv) Respirators used in fit testing and training shall be cleaned and disinfected
after each use.
(2) Storage. The employer shall ensure that respirators are stored as follows:

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(i) All respirators shall be stored to protect them from damage, contamination, dust,
sunlight, extreme temperatures, excessive moisture, and damaging chemicals, and
they shall be packed or stored to prevent deformation of the facepiece and
exhalation valve.
(ii) In addition to the requirements of paragraph (h)(2)(i) of this section, emergency
respirators shall be:
(A) Kept accessible to the work area;
(B) Stored in compartments or in covers that are clearly marked as containing
emergency respirators; and
(C) Stored in accordance with any applicable manufacturer instructions.
(3) Inspection. (i) The employer shall ensure that respirators are inspected as
follows:
(A) All respirators used in routine situations shall be inspected before each use and
during cleaning;
(B) All respirators maintained for use in emergency situations shall be inspected at
least monthly and in accordance with the manufacturer's recommendations, and
shall be checked for proper function before and after each use; and
(C) Emergency escape-only respirators shall be inspected before being carried into
the workplace for use.
(ii) The employer shall ensure that respirator inspections include the following:
(A) A check of respirator function, tightness of connections, and the condition of
the various parts including, but not limited to, the facepiece, head straps, valves,
connecting tube, and cartridges, canisters or filters; and
(B) A check of elastomeric parts for pliability and signs of deterioration.
(iii) In addition to the requirements of paragraphs (h)(3)(i) and (ii) of this section,
self-contained breathing apparatus shall be inspected monthly. Air and oxygen
cylinders shall be maintained in a fully charged state and shall be recharged when
the pressure falls to 90% of the manufacturer's recommended pressure level. The
employer shall determine that the regulator and warning devices function properly.
(iv) For respirators maintained for emergency use, the employer shall:
(A) Certify the respirator by documenting the date the inspection was performed,
the name (or signature) of the person who made the inspection, the findings,
required remedial action, and a serial number or other means of identifying the
inspected respirator; and
(B) Provide this information on a tag or label that is attached to the storage
compartment for the respirator, is kept with the respirator, or is included in
inspection reports stored as paper or electronic files. This information shall be
maintained until replaced following a subsequent certification.
(4) Repairs. The employer shall ensure that respirators that fail an inspection or are

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

otherwise found to be defective are removed from service, and are discarded or
repaired or adjusted in accordance with the following procedures:
(i) Repairs or adjustments to respirators are to be made only by persons
appropriately trained to perform such operations and shall use only the respirator
manufacturer's NIOSH-approved parts designed for the respirator;
(ii) Repairs shall be made according to the manufacturer's recommendations and
specifications for the type and extent of repairs to be performed; and
(iii) Reducing and admission valves, regulators, and alarms shall be adjusted or
repaired only by the manufacturer or a technician trained by the manufacturer.
(i) Breathing air quality and use. This paragraph requires the employer to provide
employees using atmosphere-supplying respirators (supplied-air and SCBA) with
breathing gases of high purity.
(1) The employer shall ensure that compressed air, compressed oxygen, liquid air,
and liquid oxygen used for respiration accords with the following specifications:
(i) Compressed and liquid oxygen shall meet the United States Pharmacopoeia
requirements for medical or breathing oxygen; and
(ii) Compressed breathing air shall meet at least the requirements for Grade D
breathing air described in ANSI/Compressed Gas Association Commodity
Specification for Air, G–7.1–1989, to include:
(A) Oxygen content (v/v) of 19.5–23.5%;
(B) Hydrocarbon (condensed) content of 5 milligrams per cubic meter of air or
less;
(C) Carbon monoxide (CO) content of 10 ppm or less;
(D) Carbon dioxide content of 1,000 ppm or less; and
(E) Lack of noticeable odor.
(2) The employer shall ensure that compressed oxygen is not used in atmospheresupplying respirators that have previously used compressed air.
(3) The employer shall ensure that oxygen concentrations greater than 23.5% are
used only in equipment designed for oxygen service or distribution.
(4) The employer shall ensure that cylinders used to supply breathing air to
respirators meet the following requirements:
(i) Cylinders are tested and maintained as prescribed in the Shipping Container
Specification Regulations of the Department of Transportation (49 CFR part 180);
(ii) Cylinders of purchased breathing air have a certificate of analysis from the
supplier that the breathing air meets the requirements for Grade D breathing air;
and
(iii) The moisture content in the cylinder does not exceed a dew point of -50 °F (45.6 °C) at 1 atmosphere pressure.
http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(5) The employer shall ensure that compressors used to supply breathing air to
respirators are constructed and situated so as to:
(i) Prevent entry of contaminated air into the air-supply system;
(ii) Minimize moisture content so that the dew point at 1 atmosphere pressure is 10
degrees F (5.56 °C) below the ambient temperature;
(iii) Have suitable in-line air-purifying sorbent beds and filters to further ensure
breathing air quality. Sorbent beds and filters shall be maintained and replaced or
refurbished periodically following the manufacturer's instructions.
(iv) Have a tag containing the most recent change date and the signature of the
person authorized by the employer to perform the change. The tag shall be
maintained at the compressor.
(6) For compressors that are not oil-lubricated, the employer shall ensure that
carbon monoxide levels in the breathing air do not exceed 10 ppm.
(7) For oil-lubricated compressors, the employer shall use a high-temperature or
carbon monoxide alarm, or both, to monitor carbon monoxide levels. If only hightemperature alarms are used, the air supply shall be monitored at intervals
sufficient to prevent carbon monoxide in the breathing air from exceeding 10 ppm.
(8) The employer shall ensure that breathing air couplings are incompatible with
outlets for nonrespirable worksite air or other gas systems. No asphyxiating
substance shall be introduced into breathing air lines.
(9) The employer shall use only the respirator manufacturer's NIOSH-approved
breathing-gas containers, marked and maintained in accordance with the Quality
Assurance provisions of the NIOSH approval for the SCBA as issued in accordance
with the NIOSH respirator-certification standard at 42 CFR part 84.
(j) Identification of filters, cartridges, and canisters. The employer shall ensure that
all filters, cartridges and canisters used in the workplace are labeled and color
coded with the NIOSH approval label and that the label is not removed and
remains legible.
(k) Training and information. This paragraph requires the employer to provide
effective training to employees who are required to use respirators. The training
must be comprehensive, understandable, and recur annually, and more often if
necessary. This paragraph also requires the employer to provide the basic
information on respirators in appendix D of this section to employees who wear
respirators when not required by this section or by the employer to do so.
(1) The employer shall ensure that each employee can demonstrate knowledge of at
least the following:
(i) Why the respirator is necessary and how improper fit, usage, or maintenance
can compromise the protective effect of the respirator;
(ii) What the limitations and capabilities of the respirator are;
(iii) How to use the respirator effectively in emergency situations, including

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

situations in which the respirator malfunctions;
(iv) How to inspect, put on and remove, use, and check the seals of the respirator;
(v) What the procedures are for maintenance and storage of the respirator;
(vi) How to recognize medical signs and symptoms that may limit or prevent the
effective use of respirators; and
(vii) The general requirements of this section.
(2) The training shall be conducted in a manner that is understandable to the
employee.
(3) The employer shall provide the training prior to requiring the employee to use a
respirator in the workplace.
(4) An employer who is able to demonstrate that a new employee has received
training within the last 12 months that addresses the elements specified in
paragraph (k)(1)(i) through (vii) is not required to repeat such training provided
that, as required by paragraph (k)(1), the employee can demonstrate knowledge of
those element(s). Previous training not repeated initially by the employer must be
provided no later than 12 months from the date of the previous training.
(5) Retraining shall be administered annually, and when the following situations
occur:
(i) Changes in the workplace or the type of respirator render previous training
obsolete;
(ii) Inadequacies in the employee's knowledge or use of the respirator indicate that
the employee has not retained the requisite understanding or skill; or
(iii) Any other situation arises in which retraining appears necessary to ensure safe
respirator use.
(6) The basic advisory information on respirators, as presented in appendix D of
this section, shall be provided by the employer in any written or oral format, to
employees who wear respirators when such use is not required by this section or by
the employer.
(l) Program evaluation. This section requires the employer to conduct evaluations
of the workplace to ensure that the written respiratory protection program is being
properly implemented, and to consult employees to ensure that they are using the
respirators properly.
(1) The employer shall conduct evaluations of the workplace as necessary to ensure
that the provisions of the current written program are being effectively
implemented and that it continues to be effective.
(2) The employer shall regularly consult employees required to use respirators to
assess the employees' views on program effectiveness and to identify any
problems. Any problems that are identified during this assessment shall be
corrected. Factors to be assessed include, but are not limited to:

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(i) Respirator fit (including the ability to use the respirator without interfering with
effective workplace performance);
(ii) Appropriate respirator selection for the hazards to which the employee is
exposed;
(iii) Proper respirator use under the workplace conditions the employee encounters;
and
(iv) Proper respirator maintenance.
(m) Recordkeeping. This section requires the employer to establish and retain
written information regarding medical evaluations, fit testing, and the respirator
program. This information will facilitate employee involvement in the respirator
program, assist the employer in auditing the adequacy of the program, and provide
a record for compliance determinations by OSHA.
(1) Medical evaluation. Records of medical evaluations required by this section
must be retained and made available in accordance with 29 CFR 1910.1020.
(2) Fit testing. (i) The employer shall establish a record of the qualitative and
quantitative fit tests administered to an employee including:
(A) The name or identification of the employee tested;
(B) Type of fit test performed;
(C) Specific make, model, style, and size of respirator tested;
(D) Date of test; and
(E) The pass/fail results for QLFTs or the fit factor and strip chart recording or
other recording of the test results for QNFTs.
(ii) Fit test records shall be retained for respirator users until the next fit test is
administered.
(3) A written copy of the current respirator program shall be retained by the
employer.
(4) Written materials required to be retained under this paragraph shall be made
available upon request to affected employees and to the Assistant Secretary or
designee for examination and copying.
(n) Effective date. Paragraphs (d)(3)(i)(A) and (d)(3)(i)(B) of this section become
effective November 22, 2006.
(o) Appendices. Compliance with Appendix A, Appendix B–1, Appendix B–2,
Appendix C, and Appendix D to this section are mandatory.
Appendix A to §1910.134—Fit Testing Procedures (Mandatory)
Part I. OSHA-Accepted Fit Test Protocols
A. Fit Testing Procedures—General Requirements
The employer shall conduct fit testing using the following procedures. The requirements in this

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

appendix apply to all OSHA-accepted fit test methods, both QLFT and QNFT.
1. The test subject shall be allowed to pick the most acceptable respirator from a sufficient number of
respirator models and sizes so that the respirator is acceptable to, and correctly fits, the user.
2. Prior to the selection process, the test subject shall be shown how to put on a respirator, how it
should be positioned on the face, how to set strap tension and how to determine an acceptable fit. A
mirror shall be available to assist the subject in evaluating the fit and positioning of the respirator. This
instruction may not constitute the subject's formal training on respirator use, because it is only a
review.
3. The test subject shall be informed that he/she is being asked to select the respirator that provides the
most acceptable fit. Each respirator represents a different size and shape, and if fitted and used properly,
will provide adequate protection.
4. The test subject shall be instructed to hold each chosen facepiece up to the face and eliminate those
that obviously do not give an acceptable fit.
5. The more acceptable facepieces are noted in case the one selected proves unacceptable; the most
comfortable mask is donned and worn at least five minutes to assess comfort. Assistance in assessing
comfort can be given by discussing the points in the following item A.6. If the test subject is not
familiar with using a particular respirator, the test subject shall be directed to don the mask several
times and to adjust the straps each time to become adept at setting proper tension on the straps.
6. Assessment of comfort shall include a review of the following points with the test subject and
allowing the test subject adequate time to determine the comfort of the respirator:
(a) Position of the mask on the nose
(b) Room for eye protection
(c) Room to talk
(d) Position of mask on face and cheeks
7. The following criteria shall be used to help determine the adequacy of the respirator fit:
(a) Chin properly placed;
(b) Adequate strap tension, not overly tightened;
(c) Fit across nose bridge;
(d) Respirator of proper size to span distance from nose to chin;
(e) Tendency of respirator to slip;
(f) Self-observation in mirror to evaluate fit and respirator position.
8. The test subject shall conduct a user seal check, either the negative and positive pressure seal checks
described in appendix B–1 of this section or those recommended by the respirator manufacturer which
provide equivalent protection to the procedures in appendix B–1. Before conducting the negative and
positive pressure checks, the subject shall be told to seat the mask on the face by moving the head from
side-to-side and up and down slowly while taking in a few slow deep breaths. Another facepiece shall
be selected and retested if the test subject fails the user seal check tests.
9. The test shall not be conducted if there is any hair growth between the skin and the facepiece sealing
surface, such as stubble beard growth, beard, mustache or sideburns which cross the respirator sealing
surface. Any type of apparel which interferes with a satisfactory fit shall be altered or removed.
10. If a test subject exhibits difficulty in breathing during the tests, she or he shall be referred to a
physician or other licensed health care professional, as appropriate, to determine whether the test
subject can wear a respirator while performing her or his duties.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

11. If the employee finds the fit of the respirator unacceptable, the test subject shall be given the
opportunity to select a different respirator and to be retested.
12. Exercise regimen. Prior to the commencement of the fit test, the test subject shall be given a
description of the fit test and the test subject's responsibilities during the test procedure. The description
of the process shall include a description of the test exercises that the subject will be performing. The
respirator to be tested shall be worn for at least 5 minutes before the start of the fit test.
13. The fit test shall be performed while the test subject is wearing any applicable safety equipment
that may be worn during actual respirator use which could interfere with respirator fit.
14. Test Exercises. (a) Employers must perform the following test exercises for all fit testing methods
prescribed in this appendix, except for the CNP quantitative fit testing protocol and the CNP REDON
quantitative fit testing protocol. For these two protocols, employers must ensure that the test subjects (
i.e. , employees) perform the exercise procedure specified in part I.C.4(b) of this appendix for the CNP
quantitative fit testing protocol, or the exercise procedure described in part I.C.5(b) of this appendix for
the CNP REDON quantitative fit-testing protocol. For the remaining fit testing methods, employers
must ensure that employees perform the test exercises in the appropriate test environment in the
following manner:
(1) Normal breathing. In a normal standing position, without talking, the subject shall breathe
normally.
(2) Deep breathing. In a normal standing position, the subject shall breathe slowly and deeply, taking
caution so as not to hyperventilate.
(3) Turning head side to side. Standing in place, the subject shall slowly turn his/her head from side to
side between the extreme positions on each side. The head shall be held at each extreme momentarily
so the subject can inhale at each side.
(4) Moving head up and down. Standing in place, the subject shall slowly move his/her head up and
down. The subject shall be instructed to inhale in the up position (i.e., when looking toward the
ceiling).
(5) Talking. The subject shall talk out loud slowly and loud enough so as to be heard clearly by the test
conductor. The subject can read from a prepared text such as the Rainbow Passage, count backward
from 100, or recite a memorized poem or song.
Rainbow Passage
When the sunlight strikes raindrops in the air, they act like a prism and form a rainbow. The rainbow is
a division of white light into many beautiful colors. These take the shape of a long round arch, with its
path high above, and its two ends apparently beyond the horizon. There is, according to legend, a
boiling pot of gold at one end. People look, but no one ever finds it. When a man looks for something
beyond reach, his friends say he is looking for the pot of gold at the end of the rainbow.
(6) Grimace. The test subject shall grimace by smiling or frowning. (This applies only to QNFT
testing; it is not performed for QLFT)
(7) Bending over. The test subject shall bend at the waist as if he/she were to touch his/her toes.
Jogging in place shall be substituted for this exercise in those test environments such as shroud type
QNFT or QLFT units that do not permit bending over at the waist.
(8) Normal breathing. Same as exercise (1).
(b) Each test exercise shall be performed for one minute except for the grimace exercise which shall be
performed for 15 seconds. The test subject shall be questioned by the test conductor regarding the
comfort of the respirator upon completion of the protocol. If it has become unacceptable, another model
of respirator shall be tried. The respirator shall not be adjusted once the fit test exercises begin. Any
adjustment voids the test, and the fit test must be repeated.
B. Qualitative Fit Test (QLFT) Protocols

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

1. General
(a) The employer shall ensure that persons administering QLFT are able to prepare test solutions,
calibrate equipment and perform tests properly, recognize invalid tests, and ensure that test equipment
is in proper working order.
(b) The employer shall ensure that QLFT equipment is kept clean and well maintained so as to operate
within the parameters for which it was designed.
2. Isoamyl Acetate Protocol
Note: This protocol is not appropriate to use for the fit testing of particulate respirators. If used to fit
test particulate respirators, the respirator must be equipped with an organic vapor filter.
(a) Odor Threshold Screening
Odor threshold screening, performed without wearing a respirator, is intended to determine if the
individual tested can detect the odor of isoamyl acetate at low levels.
(1) Three 1 liter glass jars with metal lids are required.
(2) Odor-free water (e.g., distilled or spring water) at approximately 25 °C (77 °F) shall be used for the
solutions.
(3) The isoamyl acetate (IAA) (also known at isopentyl acetate) stock solution is prepared by adding 1
ml of pure IAA to 800 ml of odor-free water in a 1 liter jar, closing the lid and shaking for 30 seconds.
A new solution shall be prepared at least weekly.
(4) The screening test shall be conducted in a room separate from the room used for actual fit testing.
The two rooms shall be well-ventilated to prevent the odor of IAA from becoming evident in the
general room air where testing takes place.
(5) The odor test solution is prepared in a second jar by placing 0.4 ml of the stock solution into 500 ml
of odor-free water using a clean dropper or pipette. The solution shall be shaken for 30 seconds and
allowed to stand for two to three minutes so that the IAA concentration above the liquid may reach
equilibrium. This solution shall be used for only one day.
(6) A test blank shall be prepared in a third jar by adding 500 cc of odor-free water.
(7) The odor test and test blank jar lids shall be labeled (e.g., 1 and 2) for jar identification. Labels shall
be placed on the lids so that they can be peeled off periodically and switched to maintain the integrity
of the test.
(8) The following instruction shall be typed on a card and placed on the table in front of the two test
jars (i.e., 1 and 2): “The purpose of this test is to determine if you can smell banana oil at a low
concentration. The two bottles in front of you contain water. One of these bottles also contains a small
amount of banana oil. Be sure the covers are on tight, then shake each bottle for two seconds. Unscrew
the lid of each bottle, one at a time, and sniff at the mouth of the bottle. Indicate to the test conductor
which bottle contains banana oil.”
(9) The mixtures used in the IAA odor detection test shall be prepared in an area separate from where
the test is performed, in order to prevent olfactory fatigue in the subject.
(10) If the test subject is unable to correctly identify the jar containing the odor test solution, the IAA
qualitative fit test shall not be performed.
(11) If the test subject correctly identifies the jar containing the odor test solution, the test subject may
proceed to respirator selection and fit testing.
(b) Isoamyl Acetate Fit Test
(1) The fit test chamber shall be a clear 55-gallon drum liner suspended inverted over a 2-foot
diameter frame so that the top of the chamber is about 6 inches above the test subject's head. If no drum
liner is available, a similar chamber shall be constructed using plastic sheeting. The inside top center of

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

the chamber shall have a small hook attached.
(2) Each respirator used for the fitting and fit testing shall be equipped with organic vapor cartridges or
offer protection against organic vapors.
(3) After selecting, donning, and properly adjusting a respirator, the test subject shall wear it to the fit
testing room. This room shall be separate from the room used for odor threshold screening and
respirator selection, and shall be well-ventilated, as by an exhaust fan or lab hood, to prevent general
room contamination.
(4) A copy of the test exercises and any prepared text from which the subject is to read shall be taped
to the inside of the test chamber.
(5) Upon entering the test chamber, the test subject shall be given a 6-inch by 5-inch piece of paper
towel, or other porous, absorbent, single-ply material, folded in half and wetted with 0.75 ml of pure
IAA. The test subject shall hang the wet towel on the hook at the top of the chamber. An IAA test swab
or ampule may be substituted for the IAA wetted paper towel provided it has been demonstrated that
the alternative IAA source will generate an IAA test atmosphere with a concentration equivalent to that
generated by the paper towel method.
(6) Allow two minutes for the IAA test concentration to stabilize before starting the fit test exercises.
This would be an appropriate time to talk with the test subject; to explain the fit test, the importance of
his/her cooperation, and the purpose for the test exercises; or to demonstrate some of the exercises.
(7) If at any time during the test, the subject detects the banana-like odor of IAA, the test is failed. The
subject shall quickly exit from the test chamber and leave the test area to avoid olfactory fatigue.
(8) If the test is failed, the subject shall return to the selection room and remove the respirator. The test
subject shall repeat the odor sensitivity test, select and put on another respirator, return to the test area
and again begin the fit test procedure described in (b) (1) through (7) above. The process continues
until a respirator that fits well has been found. Should the odor sensitivity test be failed, the subject
shall wait at least 5 minutes before retesting. Odor sensitivity will usually have returned by this time.
(9) If the subject passes the test, the efficiency of the test procedure shall be demonstrated by having
the subject break the respirator face seal and take a breath before exiting the chamber.
(10) When the test subject leaves the chamber, the subject shall remove the saturated towel and return it
to the person conducting the test, so that there is no significant IAA concentration buildup in the
chamber during subsequent tests. The used towels shall be kept in a self-sealing plastic bag to keep the
test area from being contaminated.
3. Saccharin Solution Aerosol Protocol
The entire screening and testing procedure shall be explained to the test subject prior to the conduct of
the screening test.
(a) Taste threshold screening. The saccharin taste threshold screening, performed without wearing a
respirator, is intended to determine whether the individual being tested can detect the taste of saccharin.
(1) During threshold screening as well as during fit testing, subjects shall wear an enclosure about the
head and shoulders that is approximately 12 inches in diameter by 14 inches tall with at least the front
portion clear and that allows free movements of the head when a respirator is worn. An enclosure
substantially similar to the 3M hood assembly, parts # FT 14 and # FT 15 combined, is adequate.
(2) The test enclosure shall have a3/4-inch (1.9 cm) hole in front of the test subject's nose and mouth
area to accommodate the nebulizer nozzle.
(3) The test subject shall don the test enclosure. Throughout the threshold screening test, the test
subject shall breathe through his/her slightly open mouth with tongue extended. The subject is
instructed to report when he/she detects a sweet taste.
(4) Using a DeVilbiss Model 40 Inhalation Medication Nebulizer or equivalent, the test conductor shall
spray the threshold check solution into the enclosure. The nozzle is directed away from the nose and

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

mouth of the person. This nebulizer shall be clearly marked to distinguish it from the fit test solution
nebulizer.
(5) The threshold check solution is prepared by dissolving 0.83 gram of sodium saccharin USP in 100
ml of warm water. It can be prepared by putting 1 ml of the fit test solution (see (b)(5) below) in 100
ml of distilled water.
(6) To produce the aerosol, the nebulizer bulb is firmly squeezed so that it collapses completely, then
released and allowed to fully expand.
(7) Ten squeezes are repeated rapidly and then the test subject is asked whether the saccharin can be
tasted. If the test subject reports tasting the sweet taste during the ten squeezes, the screening test is
completed. The taste threshold is noted as ten regardless of the number of squeezes actually completed.
(8) If the first response is negative, ten more squeezes are repeated rapidly and the test subject is again
asked whether the saccharin is tasted. If the test subject reports tasting the sweet taste during the second
ten squeezes, the screening test is completed. The taste threshold is noted as twenty regardless of the
number of squeezes actually completed.
(9) If the second response is negative, ten more squeezes are repeated rapidly and the test subject is
again asked whether the saccharin is tasted. If the test subject reports tasting the sweet taste during the
third set of ten squeezes, the screening test is completed. The taste threshold is noted as thirty
regardless of the number of squeezes actually completed.
(10) The test conductor will take note of the number of squeezes required to solicit a taste response.
(11) If the saccharin is not tasted after 30 squeezes (step 10), the test subject is unable to taste saccharin
and may not perform the saccharin fit test.
Note to paragraph 3(a): If the test subject eats or drinks something sweet before the screening test,
he/she may be unable to taste the weak saccharin solution.
(12) If a taste response is elicited, the test subject shall be asked to take note of the taste for reference
in the fit test.
(13) Correct use of the nebulizer means that approximately 1 ml of liquid is used at a time in the
nebulizer body.
(14) The nebulizer shall be thoroughly rinsed in water, shaken dry, and refilled at least each morning
and afternoon or at least every four hours.
(b) Saccharin solution aerosol fit test procedure.
(1) The test subject may not eat, drink (except plain water), smoke, or chew gum for 15 minutes before
the test.
(2) The fit test uses the same enclosure described in 3. (a) above.
(3) The test subject shall don the enclosure while wearing the respirator selected in section I. A. of this
appendix. The respirator shall be properly adjusted and equipped with a particulate filter(s).
(4) A second DeVilbiss Model 40 Inhalation Medication Nebulizer or equivalent is used to spray the fit
test solution into the enclosure. This nebulizer shall be clearly marked to distinguish it from the
screening test solution nebulizer.
(5) The fit test solution is prepared by adding 83 grams of sodium saccharin to 100 ml of warm water.
(6) As before, the test subject shall breathe through the slightly open mouth with tongue extended, and
report if he/she tastes the sweet taste of saccharin.
(7) The nebulizer is inserted into the hole in the front of the enclosure and an initial concentration of
saccharin fit test solution is sprayed into the enclosure using the same number of squeezes (either 10,
20 or 30 squeezes) based on the number of squeezes required to elicit a taste response as noted during
the screening test. A minimum of 10 squeezes is required.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(8) After generating the aerosol, the test subject shall be instructed to perform the exercises in section I.
A. 14. of this appendix.
(9) Every 30 seconds the aerosol concentration shall be replenished using one half the original number
of squeezes used initially (e.g., 5, 10 or 15).
(10) The test subject shall indicate to the test conductor if at any time during the fit test the taste of
saccharin is detected. If the test subject does not report tasting the saccharin, the test is passed.
(11) If the taste of saccharin is detected, the fit is deemed unsatisfactory and the test is failed. A
different respirator shall be tried and the entire test procedure is repeated (taste threshold screening and
fit testing).
(12) Since the nebulizer has a tendency to clog during use, the test operator must make periodic checks
of the nebulizer to ensure that it is not clogged. If clogging is found at the end of the test session, the
test is invalid.
4. Bitrex TM (Denatonium Benzoate) Solution Aerosol Qualitative Fit Test Protocol
The Bitrex TM (Denatonium benzoate) solution aerosol QLFT protocol uses the published saccharin test
protocol because that protocol is widely accepted. Bitrex is routinely used as a taste aversion agent in
household liquids which children should not be drinking and is endorsed by the American Medical
Association, the National Safety Council, and the American Association of Poison Control Centers.
The entire screening and testing procedure shall be explained to the test subject prior to the conduct of
the screening test.
(a) Taste Threshold Screening.
The Bitrex taste threshold screening, performed without wearing a respirator, is intended to determine
whether the individual being tested can detect the taste of Bitrex.
(1) During threshold screening as well as during fit testing, subjects shall wear an enclosure about the
head and shoulders that is approximately 12 inches (30.5 cm) in diameter by 14 inches (35.6 cm) tall.
The front portion of the enclosure shall be clear from the respirator and allow free movement of the
head when a respirator is worn. An enclosure substantially similar to the 3M hood assembly, parts # FT
14 and # FT 15 combined, is adequate.
(2) The test enclosure shall have a3/4inch (1.9 cm) hole in front of the test subject's nose and mouth
area to accommodate the nebulizer nozzle.
(3) The test subject shall don the test enclosure. Throughout the threshold screening test, the test
subject shall breathe through his or her slightly open mouth with tongue extended. The subject is
instructed to report when he/she detects a bitter taste.
(4) Using a DeVilbiss Model 40 Inhalation Medication Nebulizer or equivalent, the test conductor shall
spray the Threshold Check Solution into the enclosure. This Nebulizer shall be clearly marked to
distinguish it from the fit test solution nebulizer.
(5) The Threshold Check Solution is prepared by adding 13.5 milligrams of Bitrex to 100 ml of 5%
salt (NaCl) solution in distilled water.
(6) To produce the aerosol, the nebulizer bulb is firmly squeezed so that the bulb collapses completely,
and is then released and allowed to fully expand.
(7) An initial ten squeezes are repeated rapidly and then the test subject is asked whether the Bitrex can
be tasted. If the test subject reports tasting the bitter taste during the ten squeezes, the screening test is
completed. The taste threshold is noted as ten regardless of the number of squeezes actually completed.
(8) If the first response is negative, ten more squeezes are repeated rapidly and the test subject is again
asked whether the Bitrex is tasted. If the test subject reports tasting the bitter taste during the second ten
squeezes, the screening test is completed. The taste threshold is noted as twenty regardless of the
number of squeezes actually completed.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(9) If the second response is negative, ten more squeezes are repeated rapidly and the test subject is
again asked whether the Bitrex is tasted. If the test subject reports tasting the bitter taste during the third
set of ten squeezes, the screening test is completed. The taste threshold is noted as thirty regardless of
the number of squeezes actually completed.
(10) The test conductor will take note of the number of squeezes required to solicit a taste response.
(11) If the Bitrex is not tasted after 30 squeezes (step 10), the test subject is unable to taste Bitrex and
may not perform the Bitrex fit test.
(12) If a taste response is elicited, the test subject shall be asked to take note of the taste for reference
in the fit test.
(13) Correct use of the nebulizer means that approximately 1 ml of liquid is used at a time in the
nebulizer body.
(14) The nebulizer shall be thoroughly rinsed in water, shaken to dry, and refilled at least each
morning and afternoon or at least every four hours.
(b) Bitrex Solution Aerosol Fit Test Procedure.
(1) The test subject may not eat, drink (except plain water), smoke, or chew gum for 15 minutes before
the test.
(2) The fit test uses the same enclosure as that described in 4. (a) above.
(3) The test subject shall don the enclosure while wearing the respirator selected according to section I.
A. of this appendix. The respirator shall be properly adjusted and equipped with any type particulate
filter(s).
(4) A second DeVilbiss Model 40 Inhalation Medication Nebulizer or equivalent is used to spray the fit
test solution into the enclosure. This nebulizer shall be clearly marked to distinguish it from the
screening test solution nebulizer.
(5) The fit test solution is prepared by adding 337.5 mg of Bitrex to 200 ml of a 5% salt (NaCl)
solution in warm water.
(6) As before, the test subject shall breathe through his or her slightly open mouth with tongue
extended, and be instructed to report if he/she tastes the bitter taste of Bitrex.
(7) The nebulizer is inserted into the hole in the front of the enclosure and an initial concentration of
the fit test solution is sprayed into the enclosure using the same number of squeezes (either 10, 20 or 30
squeezes) based on the number of squeezes required to elicit a taste response as noted during the
screening test.
(8) After generating the aerosol, the test subject shall be instructed to perform the exercises in section I.
A. 14. of this appendix.
(9) Every 30 seconds the aerosol concentration shall be replenished using one half the number of
squeezes used initially (e.g., 5, 10 or 15).
(10) The test subject shall indicate to the test conductor if at any time during the fit test the taste of
Bitrex is detected. If the test subject does not report tasting the Bitrex, the test is passed.
(11) If the taste of Bitrex is detected, the fit is deemed unsatisfactory and the test is failed. A different
respirator shall be tried and the entire test procedure is repeated (taste threshold screening and fit
testing).
5. Irritant Smoke (Stannic Chloride) Protocol
This qualitative fit test uses a person's response to the irritating chemicals released in the “smoke”
produced by a stannic chloride ventilation smoke tube to detect leakage into the respirator.
(a) General Requirements and Precautions

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(1) The respirator to be tested shall be equipped with high efficiency particulate air (HEPA) or P100
series filter(s).
(2) Only stannic chloride smoke tubes shall be used for this protocol.
(3) No form of test enclosure or hood for the test subject shall be used.
(4) The smoke can be irritating to the eyes, lungs, and nasal passages. The test conductor shall take
precautions to minimize the test subject's exposure to irritant smoke. Sensitivity varies, and certain
individuals may respond to a greater degree to irritant smoke. Care shall be taken when performing the
sensitivity screening checks that determine whether the test subject can detect irritant smoke to use
only the minimum amount of smoke necessary to elicit a response from the test subject.
(5) The fit test shall be performed in an area with adequate ventilation to prevent exposure of the
person conducting the fit test or the build-up of irritant smoke in the general atmosphere.
(b) Sensitivity Screening Check
The person to be tested must demonstrate his or her ability to detect a weak concentration of the
irritant smoke.
(1) The test operator shall break both ends of a ventilation smoke tube containing stannic chloride, and
attach one end of the smoke tube to a low flow air pump set to deliver 200 milliliters per minute, or an
aspirator squeeze bulb. The test operator shall cover the other end of the smoke tube with a short piece
of tubing to prevent potential injury from the jagged end of the smoke tube.
(2) The test operator shall advise the test subject that the smoke can be irritating to the eyes, lungs, and
nasal passages and instruct the subject to keep his/her eyes closed while the test is performed.
(3) The test subject shall be allowed to smell a weak concentration of the irritant smoke before the
respirator is donned to become familiar with its irritating properties and to determine if he/she can
detect the irritating properties of the smoke. The test operator shall carefully direct a small amount of
the irritant smoke in the test subject's direction to determine that he/she can detect it.
(c) Irritant Smoke Fit Test Procedure
(1) The person being fit tested shall don the respirator without assistance, and perform the required user
seal check(s).
(2) The test subject shall be instructed to keep his/her eyes closed.
(3) The test operator shall direct the stream of irritant smoke from the smoke tube toward the faceseal
area of the test subject, using the low flow pump or the squeeze bulb. The test operator shall begin at
least 12 inches from the facepiece and move the smoke stream around the whole perimeter of the mask.
The operator shall gradually make two more passes around the perimeter of the mask, moving to
within six inches of the respirator.
(4) If the person being tested has not had an involuntary response and/or detected the irritant smoke,
proceed with the test exercises.
(5) The exercises identified in section I.A. 14. of this appendix shall be performed by the test subject
while the respirator seal is being continually challenged by the smoke, directed around the perimeter of
the respirator at a distance of six inches.
(6) If the person being fit tested reports detecting the irritant smoke at any time, the test is failed. The
person being retested must repeat the entire sensitivity check and fit test procedure.
(7) Each test subject passing the irritant smoke test without evidence of a response (involuntary cough,
irritation) shall be given a second sensitivity screening check, with the smoke from the same smoke
tube used during the fit test, once the respirator has been removed, to determine whether he/she still
reacts to the smoke. Failure to evoke a response shall void the fit test.
(8) If a response is produced during this second sensitivity check, then the fit test is passed.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

C. Quantitative Fit Test (QNFT) Protocols
The following quantitative fit testing procedures have been demonstrated to be acceptable:
Quantitative fit testing using a non-hazardous test aerosol (such as corn oil, polyethylene glycol 400
[PEG 400], di-2-ethyl hexyl sebacate [DEHS], or sodium chloride) generated in a test chamber, and
employing instrumentation to quantify the fit of the respirator; Quantitative fit testing using ambient
aerosol as the test agent and appropriate instrumentation (condensation nuclei counter) to quantify the
respirator fit; Quantitative fit testing using controlled negative pressure and appropriate instrumentation
to measure the volumetric leak rate of a facepiece to quantify the respirator fit.
1. General
(a) The employer shall ensure that persons administering QNFT are able to calibrate equipment and
perform tests properly, recognize invalid tests, calculate fit factors properly and ensure that test
equipment is in proper working order.
(b) The employer shall ensure that QNFT equipment is kept clean, and is maintained and calibrated
according to the manufacturer's instructions so as to operate at the parameters for which it was
designed.
2. Generated Aerosol Quantitative Fit Testing Protocol
(a) Apparatus.
(1) Instrumentation. Aerosol generation, dilution, and measurement systems using particulates (corn
oil, polyethylene glycol 400 [PEG 400], di-2-ethyl hexyl sebacate [DEHS] or sodium chloride) as test
aerosols shall be used for quantitative fit testing.
(2) Test chamber. The test chamber shall be large enough to permit all test subjects to perform freely
all required exercises without disturbing the test agent concentration or the measurement apparatus.
The test chamber shall be equipped and constructed so that the test agent is effectively isolated from
the ambient air, yet uniform in concentration throughout the chamber.
(3) When testing air-purifying respirators, the normal filter or cartridge element shall be replaced with
a high efficiency particulate air (HEPA) or P100 series filter supplied by the same manufacturer.
(4) The sampling instrument shall be selected so that a computer record or strip chart record may be
made of the test showing the rise and fall of the test agent concentration with each inspiration and
expiration at fit factors of at least 2,000. Integrators or computers that integrate the amount of test agent
penetration leakage into the respirator for each exercise may be used provided a record of the readings
is made.
(5) The combination of substitute air-purifying elements, test agent and test agent concentration shall
be such that the test subject is not exposed in excess of an established exposure limit for the test agent
at any time during the testing process, based upon the length of the exposure and the exposure limit
duration.
(6) The sampling port on the test specimen respirator shall be placed and constructed so that no leakage
occurs around the port (e.g., where the respirator is probed), a free air flow is allowed into the sampling
line at all times, and there is no interference with the fit or performance of the respirator. The in-mask
sampling device (probe) shall be designed and used so that the air sample is drawn from the breathing
zone of the test subject, midway between the nose and mouth and with the probe extending into the
facepiece cavity at least 1/4 inch.
(7) The test setup shall permit the person administering the test to observe the test subject inside the
chamber during the test.
(8) The equipment generating the test atmosphere shall maintain the concentration of test agent
constant to within a 10 percent variation for the duration of the test.
(9) The time lag (interval between an event and the recording of the event on the strip chart or
computer or integrator) shall be kept to a minimum. There shall be a clear association between the
occurrence of an event and its being recorded.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(10) The sampling line tubing for the test chamber atmosphere and for the respirator sampling port
shall be of equal diameter and of the same material. The length of the two lines shall be equal.
(11) The exhaust flow from the test chamber shall pass through an appropriate filter (i.e., high
efficiency particulate filter) before release.
(12) When sodium chloride aerosol is used, the relative humidity inside the test chamber shall not
exceed 50 percent.
(13) The limitations of instrument detection shall be taken into account when determining the fit factor.
(14) Test respirators shall be maintained in proper working order and be inspected regularly for
deficiencies such as cracks or missing valves and gaskets.
(b) Procedural Requirements.
(1) When performing the initial user seal check using a positive or negative pressure check, the
sampling line shall be crimped closed in order to avoid air pressure leakage during either of these
pressure checks.
(2) The use of an abbreviated screening QLFT test is optional. Such a test may be utilized in order to
quickly identify poor fitting respirators that passed the positive and/or negative pressure test and reduce
the amount of QNFT time. The use of the CNC QNFT instrument in the count mode is another optional
method to obtain a quick estimate of fit and eliminate poor fitting respirators before going on to
perform a full QNFT.
(3) A reasonably stable test agent concentration shall be measured in the test chamber prior to testing.
For canopy or shower curtain types of test units, the determination of the test agent's stability may be
established after the test subject has entered the test environment.
(4) Immediately after the subject enters the test chamber, the test agent concentration inside the
respirator shall be measured to ensure that the peak penetration does not exceed 5 percent for a half
mask or 1 percent for a full facepiece respirator.
(5) A stable test agent concentration shall be obtained prior to the actual start of testing.
(6) Respirator restraining straps shall not be over-tightened for testing. The straps shall be adjusted by
the wearer without assistance from other persons to give a reasonably comfortable fit typical of normal
use. The respirator shall not be adjusted once the fit test exercises begin.
(7) The test shall be terminated whenever any single peak penetration exceeds 5 percent for half masks
and 1 percent for full facepiece respirators. The test subject shall be refitted and retested.
(8) Calculation of fit factors.
(i) The fit factor shall be determined for the quantitative fit test by taking the ratio of the average
chamber concentration to the concentration measured inside the respirator for each test exercise except
the grimace exercise.
(ii) The average test chamber concentration shall be calculated as the arithmetic average of the
concentration measured before and after each test (i.e., 7 exercises) or the arithmetic average of the
concentration measured before and after each exercise or the true average measured continuously
during the respirator sample.
(iii) The concentration of the challenge agent inside the respirator shall be determined by one of the
following methods:
( A ) Average peak penetration method means the method of determining test agent penetration into the
respirator utilizing a strip chart recorder, integrator, or computer. The agent penetration is determined
by an average of the peak heights on the graph or by computer integration, for each exercise except the
grimace exercise. Integrators or computers that calculate the actual test agent penetration into the
respirator for each exercise will also be considered to meet the requirements of the average peak
penetration method.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

( B ) Maximum peak penetration method means the method of determining test agent penetration in the
respirator as determined by strip chart recordings of the test. The highest peak penetration for a given
exercise is taken to be representative of average penetration into the respirator for that exercise.
( C ) Integration by calculation of the area under the individual peak for each exercise except the
grimace exercise. This includes computerized integration.
( D ) The calculation of the overall fit factor using individual exercise fit factors involves first
converting the exercise fit factors to penetration values, determining the average, and then converting
that result back to a fit factor. This procedure is described in the following equation:

Where ff1 , ff2 , ff3 , etc. are the fit factors for exercises 1, 2, 3, etc.
(9) The test subject shall not be permitted to wear a half mask or quarter facepiece respirator unless a
minimum fit factor of 100 is obtained, or a full facepiece respirator unless a minimum fit factor of 500
is obtained.
(10) Filters used for quantitative fit testing shall be replaced whenever increased breathing resistance is
encountered, or when the test agent has altered the integrity of the filter media.
3. Ambient aerosol condensation nuclei counter (CNC) quantitative fit testing protocol.
The ambient aerosol condensation nuclei counter (CNC) quantitative fit testing (PortacountTM )
protocol quantitatively fit tests respirators with the use of a probe. The probed respirator is only used
for quantitative fit tests. A probed respirator has a special sampling device, installed on the respirator,
that allows the probe to sample the air from inside the mask. A probed respirator is required for each
make, style, model, and size that the employer uses and can be obtained from the respirator
manufacturer or distributor. The CNC instrument manufacturer, TSI Inc., also provides probe
attachments (TSI sampling adapters) that permit fit testing in an employee's own respirator. A
minimum fit factor pass level of at least 100 is necessary for a half-mask respirator and a minimum fit
factor pass level of at least 500 is required for a full facepiece negative pressure respirator. The entire
screening and testing procedure shall be explained to the test subject prior to the conduct of the
screening test.
(a) Portacount Fit Test Requirements. (1) Check the respirator to make sure the sampling probe and
line are properly attached to the facepiece and that the respirator is fitted with a particulate filter
capable of preventing significant penetration by the ambient particles used for the fit test (e.g., NIOSH
42 CFR 84 series 100, series 99, or series 95 particulate filter) per manufacturer's instruction.
(2) Instruct the person to be tested to don the respirator for five minutes before the fit test starts. This
purges the ambient particles trapped inside the respirator and permits the wearer to make certain the
respirator is comfortable. This individual shall already have been trained on how to wear the respirator
properly.
(3) Check the following conditions for the adequacy of the respirator fit: Chin properly placed;
Adequate strap tension, not overly tightened; Fit across nose bridge; Respirator of proper size to span
distance from nose to chin; Tendency of the respirator to slip; Self-observation in a mirror to evaluate
fit and respirator position.
(4) Have the person wearing the respirator do a user seal check. If leakage is detected, determine the
cause. If leakage is from a poorly fitting facepiece, try another size of the same model respirator, or
another model of respirator.
(5) Follow the manufacturer's instructions for operating the Portacount and proceed with the test.
(6) The test subject shall be instructed to perform the exercises in section I. A. 14. of this appendix.
(7) After the test exercises, the test subject shall be questioned by the test conductor regarding the
comfort of the respirator upon completion of the protocol. If it has become unacceptable, another model

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

of respirator shall be tried.
(b) Portacount Test Instrument.
(1) The Portacount will automatically stop and calculate the overall fit factor for the entire set of
exercises. The overall fit factor is what counts. The Pass or Fail message will indicate whether or not
the test was successful. If the test was a Pass, the fit test is over.
(2) Since the pass or fail criterion of the Portacount is user programmable, the test operator shall ensure
that the pass or fail criterion meet the requirements for minimum respirator performance in this
Appendix.
(3) A record of the test needs to be kept on file, assuming the fit test was successful. The record must
contain the test subject's name; overall fit factor; make, model, style, and size of respirator used; and
date tested.
4. Controlled negative pressure (CNP) quantitative fit testing protocol.
The CNP protocol provides an alternative to aerosol fit test methods. The CNP fit test method
technology is based on exhausting air from a temporarily sealed respirator facepiece to generate and
then maintain a constant negative pressure inside the facepiece. The rate of air exhaust is controlled so
that a constant negative pressure is maintained in the respirator during the fit test. The level of pressure
is selected to replicate the mean inspiratory pressure that causes leakage into the respirator under
normal use conditions. With pressure held constant, air flow out of the respirator is equal to air flow
into the respirator. Therefore, measurement of the exhaust stream that is required to hold the pressure
in the temporarily sealed respirator constant yields a direct measure of leakage air flow into the
respirator. The CNP fit test method measures leak rates through the facepiece as a method for
determining the facepiece fit for negative pressure respirators. The CNP instrument manufacturer
Occupational Health Dynamics of Birmingham, Alabama also provides attachments (sampling
manifolds) that replace the filter cartridges to permit fit testing in an employee's own respirator. To
perform the test, the test subject closes his or her mouth and holds his/her breath, after which an air
pump removes air from the respirator facepiece at a pre-selected constant pressure. The facepiece fit is
expressed as the leak rate through the facepiece, expressed as milliliters per minute. The quality and
validity of the CNP fit tests are determined by the degree to which the in-mask pressure tracks the test
pressure during the system measurement time of approximately five seconds. Instantaneous feedback
in the form of a real-time pressure trace of the in-mask pressure is provided and used to determine test
validity and quality. A minimum fit factor pass level of 100 is necessary for a half-mask respirator and
a minimum fit factor of at least 500 is required for a full facepiece respirator. The entire screening and
testing procedure shall be explained to the test subject prior to the conduct of the screening test.
(a) CNP Fit Test Requirements.
(1) The instrument shall have a non-adjustable test pressure of 15.0 mm water pressure.
(2) The CNP system defaults selected for test pressure shall be set at -15 mm of water (-0.58 inches of
water) and the modeled inspiratory flow rate shall be 53.8 liters per minute for performing fit tests.
Note: CNP systems have built-in capability to conduct fit testing that is specific to unique work rate,
mask, and gender situations that might apply in a specific workplace. Use of system default values,
which were selected to represent respirator wear with medium cartridge resistance at a low-moderate
work rate, will allow inter-test comparison of the respirator fit.)
(3) The individual who conducts the CNP fit testing shall be thoroughly trained to perform the test.
(4) The respirator filter or cartridge needs to be replaced with the CNP test manifold. The inhalation
valve downstream from the manifold either needs to be temporarily removed or propped open.
(5) The employer must train the test subject to hold his or her breath for at least 10 seconds.
(6) The test subject must don the test respirator without any assistance from the test administrator who
is conducting the CNP fit test. The respirator must not be adjusted once the fit-test exercises begin.
Any adjustment voids the test, and the test subject must repeat the fit test.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

(7) The QNFT protocol shall be followed according to section I. C. 1. of this appendix with an
exception for the CNP test exercises.
(b) CNP Test Exercises.
(1) Normal breathing. In a normal standing position, without talking, the subject shall breathe normally
for 1 minute. After the normal breathing exercise, the subject needs to hold head straight ahead and
hold his or her breath for 10 seconds during the test measurement.
(2) Deep breathing. In a normal standing position, the subject shall breathe slowly and deeply for 1
minute, being careful not to hyperventilate. After the deep breathing exercise, the subject shall hold his
or her head straight ahead and hold his or her breath for 10 seconds during test measurement.
(3)Turning head side to side. Standing in place, the subject shall slowly turn his or her head from side
to side between the extreme positions on each side for 1 minute. The head shall be held at each extreme
momentarily so the subject can inhale at each side. After the turning head side to side exercise, the
subject needs to hold head full left and hold his or her breath for 10 seconds during test measurement.
Next, the subject needs to hold head full right and hold his or her breath for 10 seconds during test
measurement.
(4) Moving head up and down. Standing in place, the subject shall slowly move his or her head up and
down for 1 minute. The subject shall be instructed to inhale in the up position (i.e., when looking
toward the ceiling). After the moving head up and down exercise, the subject shall hold his or her head
full up and hold his or her breath for 10 seconds during test measurement. Next, the subject shall hold
his or her head full down and hold his or her breath for 10 seconds during test measurement.
(5) Talking. The subject shall talk out loud slowly and loud enough so as to be heard clearly by the test
conductor. The subject can read from a prepared text such as the Rainbow Passage, count backward
from 100, or recite a memorized poem or song for 1 minute. After the talking exercise, the subject shall
hold his or her head straight ahead and hold his or her breath for 10 seconds during the test
measurement.
(6) Grimace. The test subject shall grimace by smiling or frowning for 15 seconds.
(7) Bending Over. The test subject shall bend at the waist as if he or she were to touch his or her toes
for 1 minute. Jogging in place shall be substituted for this exercise in those test environments such as
shroud-type QNFT units that prohibit bending at the waist. After the bending over exercise, the subject
shall hold his or her head straight ahead and hold his or her breath for 10 seconds during the test
measurement.
(8) Normal Breathing. The test subject shall remove and re-don the respirator within a one-minute
period. Then, in a normal standing position, without talking, the subject shall breathe normally for 1
minute. After the normal breathing exercise, the subject shall hold his or her head straight ahead and
hold his or her breath for 10 seconds during the test measurement. After the test exercises, the test
subject shall be questioned by the test conductor regarding the comfort of the respirator upon
completion of the protocol. If it has become unacceptable, another model of a respirator shall be tried.
(c) CNP Test Instrument.
(1) The test instrument must have an effective audio-warning device, or a visual-warning device in the
form of a screen tracing, that indicates when the test subject fails to hold his or her breath during the
test. The test must be terminated and restarted from the beginning when the test subject fails to hold
his or her breath during the test. The test subject then may be refitted and retested.
(2) A record of the test shall be kept on file, assuming the fit test was successful. The record must
contain the test subject's name; overall fit factor; make, model, style and size of respirator used; and
date tested.
5. Controlled negative pressure (CNP) REDON quantitative fit testing protocol.
(a) When administering this protocol to test subjects, employers must comply with the requirements
specified in paragraphs (a) and (c) of part I.C.4 of this appendix (“Controlled negative pressure (CNP)
quantitative fit testing protocol”), as well as use the test exercises described below in paragraph (b) of

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

this protocol instead of the test exercises specified in paragraph (b) of part I.C.4 of this appendix.
(b) Employers must ensure that each test subject being fit tested using this protocol follows the exercise
and measurement procedures, including the order of administration, described below in Table A–1 of
this appendix.
Table A–1—CNP REDON Quantitative Fit Testing Protocol

Exercises1
Exercise procedure
Facing
Stand and breathe normally, without
Forward talking, for 30 seconds
Bending
Over

Bend at the waist, as if going to touch his
or her toes, for 30 seconds

Head
Shaking

For about three seconds, shake head back
and forth vigorously several times while
shouting
REDON 1 Remove the respirator mask, loosen all
facepiece straps, and then redon the
respirator mask
REDON 2 Remove the respirator mask, loosen all
facepiece straps, and then redon the
respirator mask again

Measurement procedure
Face forward, while
holding breath for 10
seconds.
Face parallel to the floor,
while holding breath for 10
seconds
Face forward, while
holding breath for 10
seconds
Face forward, while
holding breath for 10
seconds.
Face forward, while
holding breath for 10
seconds.

1 Exercises are listed in the order in which they are to be administered.

(c) After completing the test exercises, the test administrator must question each test subject regarding
the comfort of the respirator. When a test subject states that the respirator is unacceptable, the employer
must ensure that the test administrator repeats the protocol using another respirator model.
(d) Employers must determine the overall fit factor for each test subject by calculating the harmonic
mean of the fit testing exercises as follows:

Where:
N = The number of exercises;
FF 1 = The fit factor for the first exercise;
FF 2 = The fit factor for the second exercise; and
FF N= The fit factor for the nth exercise.
Part II. New Fit Test Protocols
A. Any person may submit to OSHA an application for approval of a new fit test protocol. If the
application meets the following criteria, OSHA will initiate a rulemaking proceeding under section
6(b)(7) of the OSH Act to determine whether to list the new protocol as an approved protocol in this
appendix A.
B. The application must include a detailed description of the proposed new fit test protocol. This
application must be supported by either:

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

1. A test report prepared by an independent government research laboratory (e.g., Lawrence Livermore
National Laboratory, Los Alamos National Laboratory, the National Institute for Standards and
Technology) stating that the laboratory has tested the protocol and had found it to be accurate and
reliable; or
2. An article that has been published in a peer-reviewed industrial hygiene journal describing the
protocol and explaining how test data support the protocol's accuracy and reliability.
C. If OSHA determines that additional information is required before the Agency commences a
rulemaking proceeding under this section, OSHA will so notify the applicant and afford the applicant
the opportunity to submit the supplemental information. Initiation of a rulemaking proceeding will be
deferred until OSHA has received and evaluated the supplemental information.
Appendix B–1 to §1910.134: User Seal Check Procedures (Mandatory)
The individual who uses a tight-fitting respirator is to perform a user seal check to ensure that an
adequate seal is achieved each time the respirator is put on. Either the positive and negative pressure
checks listed in this appendix, or the respirator manufacturer's recommended user seal check method
shall be used. User seal checks are not substitutes for qualitative or quantitative fit tests.
I. Facepiece Positive and/or Negative Pressure Checks
A. Positive pressure check. Close off the exhalation valve and exhale gently into the facepiece. The
face fit is considered satisfactory if a slight positive pressure can be built up inside the facepiece
without any evidence of outward leakage of air at the seal. For most respirators this method of leak
testing requires the wearer to first remove the exhalation valve cover before closing off the exhalation
valve and then carefully replacing it after the test.
B. Negative pressure check. Close off the inlet opening of the canister or cartridge(s) by covering with
the palm of the hand(s) or by replacing the filter seal(s), inhale gently so that the facepiece collapses
slightly, and hold the breath for ten seconds. The design of the inlet opening of some cartridges cannot
be effectively covered with the palm of the hand. The test can be performed by covering the inlet
opening of the cartridge with a thin latex or nitrile glove. If the facepiece remains in its slightly
collapsed condition and no inward leakage of air is detected, the tightness of the respirator is
considered satisfactory.
II. Manufacturer's Recommended User Seal Check Procedures
The respirator manufacturer's recommended procedures for performing a user seal check may be used
instead of the positive and/or negative pressure check procedures provided that the employer
demonstrates that the manufacturer's procedures are equally effective.
Appendix B–2 to §1910.134: Respirator Cleaning Procedures (Mandatory)
These procedures are provided for employer use when cleaning respirators. They are general in nature,
and the employer as an alternative may use the cleaning recommendations provided by the
manufacturer of the respirators used by their employees, provided such procedures are as effective as
those listed here in appendix B–2. Equivalent effectiveness simply means that the procedures used
must accomplish the objectives set forth in appendix B–2, i.e., must ensure that the respirator is
properly cleaned and disinfected in a manner that prevents damage to the respirator and does not cause
harm to the user.
I. Procedures for Cleaning Respirators
A. Remove filters, cartridges, or canisters. Disassemble facepieces by removing speaking diaphragms,
demand and pressure-demand valve assemblies, hoses, or any components recommended by the
manufacturer. Discard or repair any defective parts.
B. Wash components in warm (43 °C [110 °F] maximum) water with a mild detergent or with a cleaner
recommended by the manufacturer. A stiff bristle (not wire) brush may be used to facilitate the removal
of dirt.
C. Rinse components thoroughly in clean, warm (43 °C [110 °F] maximum), preferably running water.

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

Drain.
D. When the cleaner used does not contain a disinfecting agent, respirator components should be
immersed for two minutes in one of the following:
1. Hypochlorite solution (50 ppm of chlorine) made by adding approximately one milliliter of laundry
bleach to one liter of water at 43 °C (110 °F); or,
2. Aqueous solution of iodine (50 ppm iodine) made by adding approximately 0.8 milliliters of tincture
of iodine (6–8 grams ammonium and/or potassium iodide/100 cc of 45% alcohol) to one liter of water
at 43 °C (110 °F); or,
3. Other commercially available cleansers of equivalent disinfectant quality when used as directed, if
their use is recommended or approved by the respirator manufacturer.
E. Rinse components thoroughly in clean, warm (43 °C [110 °F] maximum), preferably running water.
Drain. The importance of thorough rinsing cannot be overemphasized. Detergents or disinfectants that
dry on facepieces may result in dermatitis. In addition, some disinfectants may cause deterioration of
rubber or corrosion of metal parts if not completely removed.
F. Components should be hand-dried with a clean lint-free cloth or air-dried.
G. Reassemble facepiece, replacing filters, cartridges, and canisters where necessary.
H. Test the respirator to ensure that all components work properly.
Appendix C to §1910.134: OSHA Respirator Medical Evaluation Questionnaire (Mandatory)
To the employer: Answers to questions in Section 1, and to question 9 in Section 2 of part A, do not
require a medical examination.
To the employee:
Can you read (circle one): Yes/No
Your employer must allow you to answer this questionnaire during normal working hours, or at a time
and place that is convenient to you. To maintain your confidentiality, your employer or supervisor
must not look at or review your answers, and your employer must tell you how to deliver or send this
questionnaire to the health care professional who will review it.
Part A. Section 1. (Mandatory) The following information must be provided by every employee who
has been selected to use any type of respirator (please print).
1. Today's date:____________________
2. Your name:____________________
3. Your age (to nearest year):____________________
4. Sex (circle one): Male/Female
5. Your height: __ft. __in.
6. Your weight: __ lbs.
7. Your job title:____________________
8. A phone number where you can be reached by the health care professional who reviews this
questionnaire (include the Area Code): ___
9. The best time to phone you at this number: __
10. Has your employer told you how to contact the health care professional who will review this
questionnaire (circle one): Yes/No
11. Check the type of respirator you will use (you can check more than one category):

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

a. __ N, R, or P disposable respirator (filter-mask, non-cartridge type only).
b. __ Other type (for example, half- or full-facepiece type, powered-air purifying, supplied-air, selfcontained breathing apparatus).
12. Have you worn a respirator (circle one): Yes/No
7 If “yes,” what type(s):____________________
____________________
Part A. Section 2. (Mandatory) Questions 1 through 9 below must be answered by every employee who
has been selected to use any type of respirator (please circle “yes” or “no”).
1. Do you currently smoke tobacco, or have you smoked tobacco in the last month: Yes/No
2. Have you ever had any of the following conditions?
a. Seizures: Yes/No
b. Diabetes (sugar disease): Yes/No
c. Allergic reactions that interfere with your breathing: Yes/No
d. Claustrophobia (fear of closed-in places): Yes/No
e. Trouble smelling odors: Yes/No
3. Have you ever had any of the following pulmonary or lung problems?
a. Asbestosis: Yes/No
b. Asthma: Yes/No
c. Chronic bronchitis: Yes/No
d. Emphysema: Yes/No
e. Pneumonia: Yes/No
f. Tuberculosis: Yes/No
g. Silicosis: Yes/No
h. Pneumothorax (collapsed lung): Yes/No
i. Lung cancer: Yes/No
j. Broken ribs: Yes/No
k. Any chest injuries or surgeries: Yes/No
l. Any other lung problem that you've been told about: Yes/No
4. Do you currently have any of the following symptoms of pulmonary or lung illness?
a. Shortness of breath: Yes/No
b. Shortness of breath when walking fast on level ground or walking up a slight hill or incline: Yes/No
c. Shortness of breath when walking with other people at an ordinary pace on level ground: Yes/No
d. Have to stop for breath when walking at your own pace on level ground: Yes/No
e. Shortness of breath when washing or dressing yourself: Yes/No
f. Shortness of breath that interferes with your job: Yes/No

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

g. Coughing that produces phlegm (thick sputum): Yes/No
h. Coughing that wakes you early in the morning: Yes/No
i. Coughing that occurs mostly when you are lying down: Yes/No
j. Coughing up blood in the last month: Yes/No
k. Wheezing: Yes/No
l. Wheezing that interferes with your job: Yes/No
m. Chest pain when you breathe deeply: Yes/No
n. Any other symptoms that you think may be related to lung problems: Yes/No
5. Have you ever had any of the following cardiovascular or heart problems?
a. Heart attack: Yes/No
b. Stroke: Yes/No
c. Angina: Yes/No
d. Heart failure: Yes/No
e. Swelling in your legs or feet (not caused by walking): Yes/No
f. Heart arrhythmia (heart beating irregularly): Yes/No
g. High blood pressure: Yes/No
h. Any other heart problem that you've been told about: Yes/No
6. Have you ever had any of the following cardiovascular or heart symptoms?
a. Frequent pain or tightness in your chest: Yes/No
b. Pain or tightness in your chest during physical activity: Yes/No
c. Pain or tightness in your chest that interferes with your job: Yes/No
d. In the past two years, have you noticed your heart skipping or missing a beat: Yes/No
e. Heartburn or indigestion that is not related to eating: Yes/No
f. Any other symptoms that you think may be related to heart or circulation problems: Yes/No
7. Do you currently take medication for any of the following problems?
a. Breathing or lung problems: Yes/No
b. Heart trouble: Yes/No
c. Blood pressure: Yes/No
d. Seizures (fits): Yes/No
8. If you've used a respirator, have you ever had any of the following problems? (If you've never used a
respirator, check the following space and go to question 9:)
a. Eye irritation: Yes/No
b. Skin allergies or rashes: Yes/No
c. Anxiety: Yes/No

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

d. General weakness or fatigue: Yes/No
e. Any other problem that interferes with your use of a respirator: Yes/No
9. Would you like to talk to the health care professional who will review this questionnaire about your
answers to this questionnaire: Yes/No
Questions 10 to 15 below must be answered by every employee who has been selected to use either a
full-facepiece respirator or a self-contained breathing apparatus (SCBA). For employees who have
been selected to use other types of respirators, answering these questions is voluntary.
10. Have you ever lost vision in either eye (temporarily or permanently): Yes/No
11. Do you currently have any of the following vision problems?
a. Wear contact lenses: Yes/No
b. Wear glasses: Yes/No
c. Color blind: Yes/No
d. Any other eye or vision problem: Yes/No
12. Have you ever had an injury to your ears, including a broken ear drum: Yes/No
13. Do you currently have any of the following hearing problems?
a. Difficulty hearing: Yes/No
b. Wear a hearing aid: Yes/No
c. Any other hearing or ear problem: Yes/No
14. Have you ever had a back injury: Yes/No
15. Do you currently have any of the following musculoskeletal problems?
a. Weakness in any of your arms, hands, legs, or feet: Yes/No
b. Back pain: Yes/No
c. Difficulty fully moving your arms and legs: Yes/No
d. Pain or stiffness when you lean forward or backward at the waist: Yes/No
e. Difficulty fully moving your head up or down: Yes/No
f. Difficulty fully moving your head side to side: Yes/No
g. Difficulty bending at your knees: Yes/No
h. Difficulty squatting to the ground: Yes/No
i. Climbing a flight of stairs or a ladder carrying more than 25 lbs: Yes/No
j. Any other muscle or skeletal problem that interferes with using a respirator: Yes/No
Part B Any of the following questions, and other questions not listed, may be added to the
questionnaire at the discretion of the health care professional who will review the questionnaire.
1. In your present job, are you working at high altitudes (over 5,000 feet) or in a place that has lower
than normal amounts of oxygen: Yes/No
If “yes,” do you have feelings of dizziness, shortness of breath, pounding in your chest, or other
symptoms when you're working under these conditions: Yes/No

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

2. At work or at home, have you ever been exposed to hazardous solvents, hazardous airborne
chemicals ( e.g., gases, fumes, or dust), or have you come into skin contact with hazardous chemicals:
Yes/No
If “yes,” name the chemicals if you know them:____________________
3. Have you ever worked with any of the materials, or under any of the conditions, listed below:
a. Asbestos: Yes/No
b. Silica ( e.g., in sandblasting): Yes/No
c. Tungsten/cobalt ( e.g., grinding or welding this material): Yes/No
d. Beryllium: Yes/No
e. Aluminum: Yes/No
f. Coal (for example, mining): Yes/No
g. Iron: Yes/No
h. Tin: Yes/No
i. Dusty environments: Yes/No
j. Any other hazardous exposures: Yes/No
If “yes,” describe these exposures:____________________
____________________
4. List any second jobs or side businesses you have:____________________
____________________
5. List your previous occupations:____________________
____________________
6. List your current and previous hobbies:____________________
____________________
7. Have you been in the military services? Yes/No
If “yes,” were you exposed to biological or chemical agents (either in training or combat): Yes/No
8. Have you ever worked on a HAZMAT team? Yes/No
9. Other than medications for breathing and lung problems, heart trouble, blood pressure, and seizures
mentioned earlier in this questionnaire, are you taking any other medications for any reason (including
over-the-counter medications): Yes/No
If “yes,” name the medications if you know them:____________________
10. Will you be using any of the following items with your respirator(s)?
a. HEPA Filters: Yes/No
b. Canisters (for example, gas masks): Yes/No
c. Cartridges: Yes/No
11. How often are you expected to use the respirator(s) (circle “yes” or “no” for all answers that apply
to you)?:
a. Escape only (no rescue): Yes/No
b. Emergency rescue only: Yes/No
c. Less than 5 hours per week: Yes/No

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

d. Less than 2 hours per day: Yes/No
e. 2 to 4 hours per day: Yes/No
f. Over 4 hours per day: Yes/No
12. During the period you are using the respirator(s), is your work effort:
a. Light (less than 200 kcal per hour): Yes/No
If “yes,” how long does this period last during the average shift:______hrs.______mins.
Examples of a light work effort are sitting while writing, typing, drafting, or performing light assembly
work; or standing while operating a drill press (1–3 lbs.) or controlling machines.
b. Moderate (200 to 350 kcal per hour): Yes/No
If “yes,” how long does this period last during the average shift:______hrs.______mins.
Examples of moderate work effort are sitting while nailing or filing; driving a truck or bus in urban
traffic; standing while drilling, nailing, performing assembly work, or transferring a moderate load
(about 35 lbs.) at trunk level; walking on a level surface about 2 mph or down a 5-degree grade about 3
mph; or pushing a wheelbarrow with a heavy load (about 100 lbs.) on a level surface.
c. Heavy (above 350 kcal per hour): Yes/No
If “yes,” how long does this period last during the average shift:______hrs.______mins.
Examples of heavy work are lifting a heavy load (about 50 lbs.) from the floor to your waist or
shoulder; working on a loading dock; shoveling; standing while bricklaying or chipping castings;
walking up an 8-degree grade about 2 mph; climbing stairs with a heavy load (about 50 lbs.).
13. Will you be wearing protective clothing and/or equipment (other than the respirator) when you're
using your respirator: Yes/No
If “yes,” describe this protective clothing and/or equipment:____________________
____________________
14. Will you be working under hot conditions (temperature exceeding 77 °F): Yes/No
15. Will you be working under humid conditions: Yes/No
16. Describe the work you'll be doing while you're using your respirator(s):
____________________
____________________
17. Describe any special or hazardous conditions you might encounter when you're using your
respirator(s) (for example, confined spaces, life-threatening gases):
____________________
____________________
18. Provide the following information, if you know it, for each toxic substance that you'll be exposed to
when you're using your respirator(s):
Name of the first toxic substance:____________________
Estimated maximum exposure level per shift:____________________
Duration of exposure per shift____________________
Name of the second toxic substance:____________________
Estimated maximum exposure level per shift:____________________
Duration of exposure per shift:____________________
Name of the third toxic substance:____________________
Estimated maximum exposure level per shift:____________________

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]

Electronic Code of Federal Regulations:

Duration of exposure per shift:____________________
The name of any other toxic substances that you'll be exposed to while using your respirator:
____________________
____________________
____________________
19. Describe any special responsibilities you'll have while using your respirator(s) that may affect the
safety and well-being of others (for example, rescue, security):
____________________
Appendix D to §1910.134 (Mandatory) Information for Employees Using Respirators When Not
Required Under the Standard
Respirators are an effective method of protection against designated hazards when properly selected
and worn. Respirator use is encouraged, even when exposures are below the exposure limit, to provide
an additional level of comfort and protection for workers. However, if a respirator is used improperly or
not kept clean, the respirator itself can become a hazard to the worker. Sometimes, workers may wear
respirators to avoid exposures to hazards, even if the amount of hazardous substance does not exceed
the limits set by OSHA standards. If your employer provides respirators for your voluntary use, or if
you provide your own respirator, you need to take certain precautions to be sure that the respirator
itself does not present a hazard.
You should do the following:
1. Read and heed all instructions provided by the manufacturer on use, maintenance, cleaning and care,
and warnings regarding the respirators limitations.
2. Choose respirators certified for use to protect against the contaminant of concern. NIOSH, the
National Institute for Occupational Safety and Health of the U.S. Department of Health and Human
Services, certifies respirators. A label or statement of certification should appear on the respirator or
respirator packaging. It will tell you what the respirator is designed for and how much it will protect
you.
3. Do not wear your respirator into atmospheres containing contaminants for which your respirator is
not designed to protect against. For example, a respirator designed to filter dust particles will not
protect you against gases, vapors, or very small solid particles of fumes or smoke.
4. Keep track of your respirator so that you do not mistakenly use someone else's respirator.

[63 FR 1270, Jan. 8, 1998; 63 FR 20098, 20099, Apr. 23, 1998, as amended at 69
FR 46993, Aug. 4, 2004; 71 FR 16672, Apr. 3, 2006; 71 FR 50187, Aug. 24, 2006;
73 FR 75584, Dec. 12, 2008; 76 FR 33607, June 8, 2011]
Browse Previous | Browse Next
For questions or comments regarding e-CFR editorial content, features, or design, email ecfr@nara.gov.
For questions concerning e-CFR programming and delivery issues, email webteam@gpo.gov.
Section 508 / Accessibility

http://ecfr.gpoaccess.gov/...?c=ecfr&sid=0ba605ee0d85222b5fa084d5acd5fe3c&rgn=div8&view=text&node=29:5.1.1.1.8.9.34.3&idno=29[12/29/2011 10:42:58 AM]